Devenez fournisseur Blog Nouveaux articles
S'inscrire

Prix total

0,00 €

Panier 0 Panier 0 Loading...

A28XL Brushless Outrunner 890kv

Generating Links

A28XL Brushless Outrunner 890kv

Prix:

Now save économisez 0,00 € 0,00 €

10,27 €
Déjà acheté Discontinued Product

Please continue searching for a similar product.
SKU:
A28XL-890kv
Livraison gratuite? Cliquez ici pour apprendre plus!

A28XL Brushless Outrunner 890kv

Caractéristiques:
Modèle: A28XL
Poids: 75g
Tension: 11.1v 3s Lipoly
Kv: 890rpm / v
Shaft: Diamètre 3mm
Max charge: 30A
Max Watts: 330W
Suggestion Hélice: 9047, 1047, 1147

  • Kv ( rpm / v) 890.00
  • Max Current (A) 30.00
  • Résistance ( mh ) 0.00
  • Max Tension (V) 11.00
  • (W ) 330.00
  • Arbre A ( mm ) 3.00
  • Longueur B ( mm ) 36.00
  • Can Diamètre C ( mm ) 28.00
  • Longueur Can D ( mm ) 23.00
  • Longueur totale E ( mm ) 50.00
attributeset-10
Close

Dimension Diagram Guide

  • attributeset-10

Close

Télécharger une video

Inscrivez-vous pour télécharger des vidéos, s'il vous plaît se connecter ou s'inscrire

Sujets
Trier par
Sujets les plus récents
* Surnom:

* Votre réponse:


Veuillez saisir le texte affiché dans l'image dans le champ ci-dessous
*Code de vérification:
Annuler
Soumettre
Publier un nouveau sujet
* Surnom:

* Votre sujet:



Veuillez saisir le texte affiché dans l'image dans le champ ci-dessous
*Code de vérification:
Sujet du message

Inscrivez-vous pour écrire des critiques, s'il vous plaît se connecter ou s'inscrire

Another rc pilot | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Aug 02, 2015

Put on a Kyosho soarus glider with a 9 x 5 prop and 3s battery. Was a little underpowered and ran really warm. After about the 5th flight it was toasted. The mount that came with mine was wood.

DM571 | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Jan 10, 2014

Got 4 motors. Very good! Powerful, cheap, reliable. Good weight-performance ratio. Of the drawbacks: before first flight check as tightened the bolts securing the shaft. Shaft pressed very tight and a groove for the bolt does not correspond to the hole. You can still remove the extra Thrust washers btw. Overall im very satisfied.

| Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Jun 30, 2012

Gewicht 74,29g inkl. Kabel 6cm langem Kabel, beiliegendes Befestigungskreuz aus 3mm Sperrholz

3mm Achse mit einem Saegerring fixirt - Achsenverschiebung scheint nicht ratsam,

coptor | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Jan 24, 2012

Very good motor. Runs warm at full throttle propped with 10x6 folding prop.

Very ideal and suitable replacement for the Phoenix 2000 epo glider. Take note only 2 screw holes would fit, but that's enough for me.

Highly recommended especially the low price.

GIL.SCORPION | Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Jan 18, 2012

Engine very good. Equivalent to the KD A22-15. I put on my glider 1.80 m and was perfect.



Motor muito bom. Equivale ao KD A22-15. Coloquei no meu planador de 1,80m e ficou perfeito.

jam1e | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Dec 06, 2011

Just received this motor today.

It's well made and appears good quality.

I had to reverse thes shaft, which was a pain, but a vice makes this procedure alot easier.

As has been already stated, the wires are very thin so only time will tell if they can take the current??

I'll have to solder on the 3.5mm gold male connectors. Although the exposed wire does not appear to be "varnished" so soldering should be fine.

The mount fits the motor accurately.

I'll run the motor up and added the data to this log.

So far, so good!

SLOW STIK | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Aug 20, 2011

Got four of these to use on my tri copter. Had to reverse the shafts, easy task ! Using 9x5 3 blade props and 30 amp ESC's. Motor has a bland look, all four motors vibrate without props to the point of rendering the kk board useless . Tried balancing the bell but cannot completely get the vibration out. Bell has a radial imbalance which is due to manufacture and machining . Almost useless for my intentions. Might make a good paperweight or a desk fan..... I should have bought a good brand name motor and get a good warranty and fast cheap shipping... ( IN DAYS NOT WEEKS )

brian | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Aug 07, 2011

I received my motor it looks very nice & the craftsmanship is better than i expected.Like others have said the wires are a tad thin for my taste. But you will be glad to know Hobby King staff is listening to our feedback. The motor mount issue has been resolved at least mine fit perfectly. Over all a great motor especially for the price I dont know how they do it , but HK keep up the great work. This motor is perfect for most parkflyer foamies .If the wires were a bit bigger it would get a 5 out of 5 score .I would buy this motor again & also recommend it .

Client | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Jul 22, 2011

Strong motor,well built . the mount is no good though due to spacing of drills .

jean-claude | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Jun 12, 2011

au depart bonnes caracteristiques MAIS:les roulements ont deja beaucoup de jeu, le cylindre ne tourne pas rond mais les aimants sont tres bien cales et en 3S avec une 17/10 il consomme 30A et pue le brule avec une 9/6 11A.
si il etait de bonne qualite....5 stars!!!

  1. 1
  2. 2
Téléverser un fichier

Inscrivez-vous pour télécharger des fichiers.
S'il vous plaît se connecter ou s'inscrire pour commencer à aider les amateurs maintenant!