HobbyKing 3D Filament imprimante 1.75mm ABS 1KG Spool (Blanc)

• Overall
• Quality
• Value

4

Apr 15, 2021

4

• Overall
• Quality
• Value

Very good

Apr 22, 2019

Difficult to find the right setting for this filament but there is enough there for many tests, and it's cheap too.

• Overall
• Quality
• Value

Yup it prints on a X5S

Apr 19, 2019

Works great but needs 245-250C for good layer bonding. I print with a bed temperature of 35C, crazy cool right? on vinyl sign tape and it sticks like crazy once you get the first layer close enough to stick.

• Overall
• Quality
• Value

Pretty darn good

Feb 10, 2019

Prints like a charm on Anycubic i3 Mega. Extruder 255C, bed 110C, simple enclosure and I can hardly see any warping. Seen some cheap PLA warping more than this stuff, actually. And doesn't smell as bad as ABS i printed years back. Great stuff, really.

• Overall
• Quality
• Value

Great for the price

Oct 08, 2018

So inexpensive using a Prusa P3 steel clone with a bunch of tweaks. I run this hot around 250-260 with 10% fan(after first layer or two), that works well for me to balance quality and strength. If strength isn't important then dropping the temp down will give better surface finish to the parts.
Overall though good stuff, ordering 5 more spools right now.

• Overall
• Quality
• Value

Prints like a Charm on CR-10S

Oct 07, 2018

First test on CR-10s without housing went good on a small rim diameter 50mm hight 5mm.
No warping and good surface quality so far.
Nozzle 260°C
Bed 100°C
Bed Buildtak
Housing None

• Overall
• Quality
• Value

Good for this price

Jun 13, 2018

I printed this with my Anet A8 printer and with Mk8 extruder. First time i think its trapped a lot of moisture, while is it popping. After some print i figured out that is not moisture, while the gap happening on the same side (other sides are ok). I turned off the retraction and all gap dissapeared.
I printed it at 235°C and 90°C heatbed temp.
The other solution to eliminate the gap maybe go lower temp with the hotend and i can use the retraction for less stringing.
Isn't warping if you use hairspray on glass sheet. Its holding very strong the part on the heatbed, but after cooling down you just need to take the part without force.

• Overall
• Quality
• Value

Good for this price

Jun 13, 2018

I printed this with my Anet A8 printer and with Mk8 extruder. First time i think its trapped a lot of moisture, while is it popping. After some print i figured out that is not moisture, while the gap happening on the same side (other sides are ok). I turned off the retraction and all gap dissapeared.
I printed it at 235°C and 90°C heatbed temp.
The other solution to eliminate the gap maybe go lower temp with the hotend and i can use the retraction for less stringing.
Isn't warping if you use hairspray on glass sheet. Its holding very strong the part on the heatbed, but after cooling down you just need to take the part without force.

• Overall
• Quality
• Value

Good filament

Feb 05, 2018

Printed at 250°C and bed heated at 110°C and got nice prints, without too much warping.
Printed about 500g so far without clogging.
Good for everyday prints, but not enough for really precise prints.

• Overall
• Quality
• Value

Certified Buyer Rated

Sep 23, 2016

matière parfait pour nos impression 3D, utilisé sur malyan M150, M180 et minifabrikator!! prix plus que attractif dans un support parfait. j'adore !! je le recommande