Devenez fournisseur Blog Nouveaux articles
S'inscrire

Prix total

0,00 €

Panier 0 Panier 0 Loading...

CNC en alliage d'accélérateur Bras pour les moteurs à gaz

Generating Links

CNC en alliage d'accélérateur Bras pour les moteurs à gaz

Prix:

Now save économisez 0,00 € 0,00 €

5,86 €
Expédié de:
  • Global
Déjà acheté Discontinued Product

Please continue searching for a similar product.
SKU:
017000180-0
Livraison gratuite? Cliquez ici pour apprendre plus!

CNC en alliage d'accélérateur Bras pour les moteurs à gaz - 2mm trou fileté pour pushrod ball-link / manille.

Télécharger une video

Inscrivez-vous pour télécharger des vidéos, s'il vous plaît se connecter ou s'inscrire

Sujets
Trier par
Sujets les plus récents
* Surnom:

* Votre réponse:


Veuillez saisir le texte affiché dans l'image dans le champ ci-dessous
*Code de vérification:
Annuler
Soumettre
Publier un nouveau sujet
* Surnom:

* Votre sujet:



Veuillez saisir le texte affiché dans l'image dans le champ ci-dessous
*Code de vérification:
Sujet du message

Inscrivez-vous pour écrire des critiques, s'il vous plaît se connecter ou s'inscrire

Tonyjad | Acheteur vérifié

  • Overall
  • Quality
  • Value

Works well and well made

Jun 28, 2019

Well made and works as it should also they hard to get hold of

CMANERO | Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Dec 17, 2014

Muy util y barato....

Sptfir | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Jul 15, 2013

I have used several of these on Walbro carbs to solve a common problem involving clearance and positioning of the throttle arm on my gas powered planes. Perfect fit with extended housing and arm make life hooking up the throttle much easier. I recommend them.

opjose | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Mar 28, 2013

Perfect. These arms work great with almost ANY Walboro carbed engine.



Remove the existing screw, pry off the old short arm, and insert this one. Tighten down the berg screw and you're done.



You can install a ball socket screw for a freely moving throttle linkage setup.

Dick C. | Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Feb 02, 2013

Very impressed with arm, appears chrome plated, very attractive. Fits on my RCG26 and DLE30 easily. Specs are as follows: ID is abt 4.8mm as fits throttle shaft of 4.75mm snugly, OD is 9.5mm/.375", overall HT is 18.5mm/.731", Center shaft to 2mm linkage hole is 17.35mm/.731", overall width is 25.1mm/.99". Uses a 3mX3m set screw requiring a 1.5mm hex driver. These measurements are as accurate as I could obtain using electronic caliper. I will order additional arms for other engines. Hope this helps those needing dimensions. Would work on chokes with same diameter shafts.

jozef | Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Sep 21, 2012

Very good arm for gas engines.

__BB-Q | Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Aug 10, 2012

Excellent solution to an often overlooked problem. Fits, works and alieviates problems with the choke rod fouling the throttle rod

nesperatu | Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Jun 26, 2012

fiyatna gre ok kaliteli bir rn...

Téléverser un fichier

Inscrivez-vous pour télécharger des fichiers.
S'il vous plaît se connecter ou s'inscrire pour commencer à aider les amateurs maintenant!