Conversion Corona Synthétisé Récepteur double 6Ch 72Mhz
Jetez vos cristaux, dire au revoir à des pépins! Le nouveau récepteur Corona synthétisé est ici!
Cette unité travaillera avec les émetteurs synthétisées existants ou émetteurs de cristal. En fait, la précision de ce récepteur permettra d'améliorer la performance de tous les émetteurs de cristal de 72MHz.
La nouvelle technologie mis dans la série synthétisée de récepteurs Coron est vraiment exceptionnel et va certainement vous faire réfléchir à deux fois la mise à niveau à un 2.4GHz plus cher.
Taille: 36.8 * 22 * 8.3mm
Poids: 8.2g (avec pellicule rétractable)
Sensibilité: environ 2.0ìV
Sélectivité: ± 8kHz à 65dB vers le bas
Nombre de canaux: 1-6
Filtrage: double tourné circuits RF
Filtrage: double filtre en céramique 4 élément
filtrage DSP MCU avec l'algorithme doux: Filtrage
Maj polarité: positive ou négative (auto-détection)
Moduler: FM / PPM (pulse modulation de position)
Case: Shrink wrap
Tension de fonctionnement: 4.8V ~ 6.0VDC
Courant de fonctionnement: 11mA
I still use my old 72mhz gear but needed another receiver. Bought this as it seemed to suit my needs. Tried to bind it with my Futaba 4 channel transmitter first with not much luck. Rx would occasionally find tx signal but would never lock. After trying for over 2 hrs, I abandoned the Futaba tx and tried with my Hitec tx. Receiver found the signal instantly, and got signal lock on first attempt. Still need to do a proper range check but I'm confident it will pass the test.what a complete load of rubbish................... every time one switches on, the end points and the lengths of travel or both have changed. THIS IS NOT A PRECISION INSTRUMENT Don't wast your money on this
gregosan 1 points - 10/16/2013I have a HiTech Flash4 radio with 5 model memory. I was unable to get compatible receivers for this radio, so based on some reading and a suggestion on a forum I went with this. I ordered 2 since the price was low, and the shipping was the same as on 1. I have installed the first in my old sailplane, and it tests out perfectly. I am just waiting for good weather to fly it. The second unit also tests out perfectly. It will be going into a powered airplane soon. It is nice to get extra life out of this older, but not very old equipment without spending hundreds on a new transmitter.Muy bien . Buena relacin precio y calidad . Se acoplo perfectamente a un viejo equipo airtronicsThis is a wonderful receiver with long range and good accuracy. Setting up is a bit bumpy, But once you press scan button you will eventually succeed. Don't forget to take the prop off during set up. I highly recommend this Rx.Nice little receiver, lightweight and synced with no problems with both my JR F400 and XF631. I like it!This receiver's range is about 20 feet without glitching. Beyond that my heli gets twitchy. Also the setup instructions in the manual are not correct or clear. I got it bound to my transmitter (a Futaba 7C) but it did not go down like the instructions say so.
This is going into the trash.They are the best for synthesized receivers..have good range and lock to my futaba 6exap very well. good for park flyers and upto .40 size planes. Wont go for further up.So far Im a little dissapointed with this . No problem ( other than a bit of head scratching ) syncing , even got the fail safe set , but range is poor . Starts glitching at about 15 meters ,which is less than half my old cristal recievers . ( and its bad glitching , not just an occasional flick ) .May be okay in the foamy that its in ,( only flown close in so far ) but not very confidence inspiring .Think I might consider 2.4I have a Futaba 6XAs transmitter on channel 35. I bought one of these Corona 6 channel synthesized Rxs. It bound fine. First flight was uneventful except a few motor gltches. The next day I flew again and at around 500 feet away it went into fail-safe mode, circling at half throttle with no control response. It wound up 60 feet high in a tree. I tried switching the Tx on and off and got it back into responding, but not enough power to get it out of the tree.
I cannot tell if this is a binding, range or interference problem. I fly in an area that I would expect a lot of RF, near an airport and also with a cell tower less than a half mile away. But I think I would not use this for a large and powerful plane or full range, as it was less than 500 feet away when I lost control. The fail safe worked well though, except for the tree!