Devenez fournisseur Blog Nouveaux articles
S'inscrire

Prix total

0,00 €

Panier 0 Panier 0 Loading...

EDF55 Ducted Logement pour 55mm système

Generating Links

EDF55 Ducted Logement pour 55mm système

Prix:

Now save économisez 0,00 € 0,00 €

2,99 €
Expédié de:
  • Global
Déjà acheté
Heure d'arrivée estimée: Aucune Heure D'arrivée Estimée [ ? ]
Statut:
Epuisé!
SKU:
EDF55-DHS
Livraison gratuite? Cliquez ici pour apprendre plus!
EDF55 Ducted Logement pour 55mm système
* Case seulement.
Télécharger une video

Inscrivez-vous pour télécharger des vidéos, s'il vous plaît se connecter ou s'inscrire

Sujets
Trier par
Sujets les plus récents
* Surnom:

* Votre réponse:


Veuillez saisir le texte affiché dans l'image dans le champ ci-dessous
*Code de vérification:
Annuler
Soumettre
Publier un nouveau sujet
* Surnom:

* Votre sujet:



Veuillez saisir le texte affiché dans l'image dans le champ ci-dessous
*Code de vérification:
Sujet du message

Inscrivez-vous pour écrire des critiques, s'il vous plaît se connecter ou s'inscrire

eldiablo155 | Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Dec 30, 2014

good product with some reinforcement , the bad side is : this thing should work with small engines , and where the engine should be anchored by screws the plastic layer is too much, it would be perfect if it was less ticker

Ral fRotten | Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

May 22, 2014

The fan blades for this need to be 55mm, the actual housing is 58mm, and the rolled edge of the intake lip is 70mm outside diameter, there are 3legs on it and not 4 as shown in the picture, 1 leg is hollow for the motor wires, I intended to use it as a motor mount for a pusher but the 58mm is too wide, so back to the drawing board for me.

Grazy | Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Sep 29, 2012

4 stars just for safety. Received 2 of these and one had a few imperfections, but could easly be fixed with an exacto knife. The other one is perfect. Mine have only 3 spokes. I like the one hollow spoke. The three motor wires fit tight, but neatly through. Out of the way and it look much better than open wires. Have not run it, but I foresee no problem. Well made.

EODPete | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Sep 12, 2012

Really thick hard plastic. Seems stronger then the fan unit it is replacing. Mine is differnt then the one pictured, mine only has two mounting points. The mounting tab is really thick and I need to find longer screws to mount my EDF.

__bare | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Jul 15, 2012

This is an OLD and obsolete version fan housing.
Current versions a have a tube for motor wire exit.
Caveat Emptor

benw | Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Apr 19, 2011

Good EDF housing. No need to worry about the exiting wires from the motor with this EDF Housing. I prefre these units. With the GWS units I have, I had to cut holes to allow for the exiting wires of motor.

smasher41 | Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Jun 27, 2010

Odd fan unit but works with motors that dont ahve a standoff, also had hole pattern than accepted larger screws than most.

seems nice and round also

Fichiers clients
No File Name Download [364]
Téléverser un fichier

Inscrivez-vous pour télécharger des fichiers.
S'il vous plaît se connecter ou s'inscrire pour commencer à aider les amateurs maintenant!