New Items Forum
S'inscrire

Total Price

0,00 €

Panier 0 Panier 0 Loading...

EDF64 avec 144W C20 Moteur assemblé

EDF64 avec 144W C20 Moteur assemblé

Shipped From:
  • Global
Discontinued Product

Please continue searching for a similar product.
SKU:
EDF64-C20
WANT FREE SHIPPING? Click here to find out more!
EDF64 avec 144W C20 Moteur assemblé
Avec le moteur C20Pro, cette unité EDF fournit un bon équilibre entre traction et poussée actuelle.


Spec.
Tension d'essai: 11.1v (3S)
Testez: 13A
Thrust: 420g
Puissance: 144.3W
Moteur: C20pro 3600kv
  • UGS EDF64-C20
  • Brand -
  • Capacité ( mAh ) -
  • Poids 250.0000
  • Longueur 0.00
  • Packaging Width 0.00
  • la taille 0.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Muito bom, ultrapassa as minhas espectativas. Assobia nas horas!!!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Muito bom, ultrapassa as minhas espectativas. Assobia nas horas!!!

Just recieved Mine. Seems OK Motor bell can be pulled back approx 4mm that Definitely needs looking into. Also evidence of Fan rubbing on the Duct, motor/rotor is Not centered. Were these factory 'test run' ? Or did I get a Used 'return' unit as only running it could cause these markings.

Could be Fine.. with a rebuild, I hope. I'm also thinking I should have gotten the ADH 300 version as that motor is at least twice as long.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Just recieved Mine. Seems OK Motor bell can be pulled back approx 4mm that Definitely needs looking into. Also evidence of Fan rubbing on the Duct, motor/rotor is Not centered. Were these factory 'test run' ? Or did I get a Used 'return' unit as only running it could cause these markings.

Could be Fine.. with a rebuild, I hope. I'm also thinking I should have gotten the ADH 300 version as that motor is at least twice as long.

Yesterday I maid my first testrund in my selfmaid depron FW TA-183 "Huckebein" (Destweight 350 gr.) with a 20 Amp RX and 1000mAh 3S Lipo and what should I say "Wauh"... The model makes a lot of noise and produces a lot of thrust !

Thx Hobby City

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Yesterday I maid my first testrund in my selfmaid depron FW TA-183 "Huckebein" (Destweight 350 gr.) with a 20 Amp RX and 1000mAh 3S Lipo and what should I say "Wauh"... The model makes a lot of noise and produces a lot of thrust !

Thx Hobby City

EDF housing appears to be a GWS or clone housing. Outrunner motor makes a nice light EDF unit.



But, I only measured 320 grams of thrust @ 13.5A, 11.1v on a Zippy-H 30-40C 2500mah, using a Turnigy 25amp ESC. Both motors gave the same thrust, so the advertised 420 seems a bit suspect (unless I got two duff motors). I wonder if they'd survive 4s...



Build quality on one motor was also very poor. The stator wasn't pushed down the bearing tube entirely, so the end of the bell was able to rub against the stator coils (and rub off insulation) when pulled forward (e.g. by the fan thrust). Fortunately I noticed this before running the motor, and was able to force the stator down the tube by gently clamping it in a bench vise between soft wood blocks.

Other motor was fine, though the set screws look easy to strip if you're not careful.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

EDF housing appears to be a GWS or clone housing. Outrunner motor makes a nice light EDF unit.



But, I only measured 320 grams of thrust @ 13.5A, 11.1v on a Zippy-H 30-40C 2500mah, using a Turnigy 25amp ESC. Both motors gave the same thrust, so the advertised 420 seems a bit suspect (unless I got two duff motors). I wonder if they'd survive 4s...



Build quality on one motor was also very poor. The stator wasn't pushed down the bearing tube entirely, so the end of the bell was able to rub against the stator coils (and rub off insulation) when pulled forward (e.g. by the fan thrust). Fortunately I noticed this before running the motor, and was able to force the stator down the tube by gently clamping it in a bench vise between soft wood blocks.

Other motor was fine, though the set screws look easy to strip if you're not careful.

Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!