Devenez fournisseur Blog Nouveaux articles
S'inscrire

Prix total

0,00 €

Panier 0 Panier 0 Loading...

Flycolor X-Cross BL-32 4-in-1 40A Brushless ESC

Generating Links

Flycolor X-Cross BL-32 4-in-1 40A Brushless ESC

Prix:

Now save économisez 0,00 € 0,00 €

53,14 €
Statut:
Epuisé!
SKU:
9261000073-0
Livraison gratuite? Cliquez ici pour apprendre plus!

The Flycolor X-Cross BL-32 ESCs are a high-powered addition to your FPV drone. The built-in 32-bit processor and Flycolor_X_Cross_BL_32 firmware gives a quick response to any situation. This excellent 4-in1 ESC board fits easily into a 30.5x30.5mm tower and is complete with a 5V/1.5A BEC.

 

These ESC’s come with a top-class MOSFET that has less inner resistance which helps allow larger current throughput which allows for higher KV motors and more power load. The metalized contact edge provides an excellent soldering point for stronger contact. The 40A 4in1 ESC comes with a highly efficient aluminum heat sink for better heat dissipation.

 

Get the Flycolor X-Cross BL-32 4in1 ESC now for faster response and better control of your drone.

 

Features:
• ARM 32-bit Cortex MCU, frequency up to 48 MHZ
• Flycolor_X_Cross_BL_32 firmware, which is designed for superior functionality and performance
• 4 in 1 ESC with builtin current sensor and 5V/1.5A BEC and VBAT output
• Supports regular 1-2ms pulse width input, as well as Oneshot125 (125-250us), Oneshot42 (41.7-83.3us) and Multshot (5- 25us). The input signal is automatically detected by the ESC upon power up
• Dshot signal is supported at any rate up to at least Dshot1200
• Damped light does regenerative braking, causing very fast motor retardation, and inherently also does active freewheeling
• Quick connector on board which is compatible with most flight controllers
• Large area aluminum heat sink effectively slow down the temperature rise
• Built for 30.5x30.5mm tower
• Faster response, less lag

 

Specs:
Battery: 3~6S
Continuous Current: 40A
Burst Current: 50A (10s)
BEC: 5V/1.5A
Heatsink: Yes
Install holes: 30.5x30.5mm, M3
Size: 34x41x8mm
Weight: 16g
Firmware: Flycolor_X_Cross_BL_32
Typical Applications: 170-450 multirotor

 

Includes:
1 x X-Cross  BL-32 4in1 ESC
8 x Nylon Nut M3
4 x Screw M3x16mm
4 x Nylon spacer M3x6+6
1 x Power line plus XT60
1 x 8-pin SH1.0 cable
1 x Capacitor

Télécharger une video

Inscrivez-vous pour télécharger des vidéos, s'il vous plaît se connecter ou s'inscrire

Sujets
Trier par
Sujets les plus récents
* Surnom:

* Votre réponse:


Veuillez saisir le texte affiché dans l'image dans le champ ci-dessous
*Code de vérification:
Annuler
Soumettre
Publier un nouveau sujet
* Surnom:

* Votre sujet:



Veuillez saisir le texte affiché dans l'image dans le champ ci-dessous
*Code de vérification:
Sujet du message

Inscrivez-vous pour écrire des critiques, s'il vous plaît se connecter ou s'inscrire

Connor | Acheteur vérifié

  • Overall
  • Quality
  • Value

Good ESC, Some Issues Though

Apr 21, 2019

This ESC is a good size 4-in-1 which looks nice and was easy to install. The ESC is responsive and works with my motors just fine. I did have a couple of issues programming the unit, specifically to do with the motors not spinning at all when armed. I re-flashed the firmware, made sure all drivers were installed, and reconfigured the ESC and then it worked fine. I'm not sure if my issues were to do with me or the ESC itself, but it was a bit fiddly to set up. Also, the S1 to S4 cables were way too short to solder onto pads, make sure to have some spare wire to extend them.
Otherwise, this ESC is pretty solid, but it is expensive. I'm not sure if I'd go with a 4-in-1 again.

Fichiers clients
Flycolor X-Cross BL-32 4in1 40A ESC Manual Download [698]
Téléverser un fichier

Inscrivez-vous pour télécharger des fichiers.
S'il vous plaît se connecter ou s'inscrire pour commencer à aider les amateurs maintenant!