New Items Forum
S'inscrire

Total Price

0,00 €

Panier 0 Panier 0 Loading...

FPV Radio Telemetry Kit - 915 MHz

FPV Radio Telemetry Kit - 915 MHz

Discontinued Product

Please continue searching for a similar product.
Poids
50 g
SKU:
9387000010
WANT FREE SHIPPING? Click here to find out more!

Ce kit Radio Telemetry offre un prix bas, une plus longue portée (environ une mile avec des antennes fournies) et des performances supérieures. Le système utilise la bande 915MHz et fournit un lien full-duplex en utilisant les modules HM-TRP de HopeRF en cours d'exécution personnalisées, open source, firmware.

Le firmware SiK comprend un bootloader qui permet des mises à niveau du micrologiciel de radio sur l'interface série, et la configuration des paramètres du système. les mises à jour du micrologiciel et la configuration sont entièrement pris en charge dans le planificateur APM Mission. La configuration est également possible grâce au configurateur 3DR Radio et commandes AT.

Interface au module se fait par série / FT232 série standard USB TTL 5V tolérantes.

Caractéristiques:
• Très petite taille
• Poids léger (moins de 4 grammes sans antenne)
• bande de fréquence 915MHz
• Sensibilité du récepteur -117 dBm
• La puissance d'émission jusqu'à 20dBm (100mW)
• liaison série Transparent
• Taux de données d'air jusqu'à 250kbps
• Gamme d'environ 1 mile avec des antennes fournies
• Plage démontrée de plusieurs kilomètres avec une petite antenne omnidirectionnelle
• Peut être utilisé avec un amplificateur bi-directionnel pour encore plus de gamme
• protocole MAVLink cadrage et de l'état des rapports
• spectre à sauts de fréquence de propagation (FHSS)
• Temps Adaptive division multiplexing (TDM)
• Prise en charge LBT et AFA
• cyclique Configurable
• Construit en code correcteur d'erreurs (peut corriger jusqu'à 25% d'erreurs de bits de données)
• firmware open source
• commandes AT pour la configuration de la radio
• RT commandes pour la configuration de la radio à distance
• le contrôle de flux adaptatif lorsqu'il est utilisé avec APM
• Basé sur le module radio HopeRF HM-TRP, avec un microcontrôleur SiLabs SI1000 RF.


Spécifications:
Band: 915MHz
Connecteurs d'antenne: connecteur RP-SMA
Puissance de sortie: 100mW (20dBm), réglable entre 1-20dBm
Sensibilité: Sensibilité -117dBm
Interface: TTL standard UART
Etat de la connexion: indicateurs LED


Comprend:
Radio Telemetry station de base (Connexion USB)
Télémétrie Transceiver (Pin Header)
plomb ensemble x1
Antenne x 2

Ce produit est basé sur le 3DRadio projet de robotique 3D.

  • UGS 9387000010
  • Brand -
  • Capacité ( mAh ) -
  • Poids (g) 50.00
  • Longueur 120.00
  • Largeur 25.00
  • la taille 80.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Using this with APM 2.5 and Mission Planner. Worked out of the box, no issues whatsoever. Highly recommended.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Using this with APM 2.5 and Mission Planner. Worked out of the box, no issues whatsoever. Highly recommended.

For the money you can't do much better...comes with all the features I need. Works well with APM 2.5

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

For the money you can't do much better...comes with all the features I need. Works well with APM 2.5

Works great. Using it with Ardupilot APM 2.5.



1. Opened mission planner

2. Choose the correct com port

3. Go to 3dr configuration page

4. 'Load settings'

5. Updated the firmware

6. Connected to APM



Easy! Have flown and is a lot of fun to click where you want the copter to go.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Works great. Using it with Ardupilot APM 2.5.



1. Opened mission planner

2. Choose the correct com port

3. Go to 3dr configuration page

4. 'Load settings'

5. Updated the firmware

6. Connected to APM



Easy! Have flown and is a lot of fun to click where you want the copter to go.

Excellent. Plug n Play with APM 2.5.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Excellent. Plug n Play with APM 2.5.

I don't use APM or mission planner so i don't know if it working that way.On the bench test,with the original 3DR config tool everything worked perfect.The latest SiK firmware upgrade is made within 2 minutes both for ground and air module.With 1dbm level and not so cellular friendly enviroment i went 20 more or less meters away till my ground control software announced out of signal,but with a lot of noise according to rssi meter.I had a very little problem in changing baud rate for my FY21AP,needed a little reading...The stock whip antennas are not 900 mhz exactly or...they need to be tuned,or change them with an inverted vee dipole for perfect signal range and noise levels.Very happy for this 3dr clone.Ready to buy the 433mhz version!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I don't use APM or mission planner so i don't know if it working that way.On the bench test,with the original 3DR config tool everything worked perfect.The latest SiK firmware upgrade is made within 2 minutes both for ground and air module.With 1dbm level and not so cellular friendly enviroment i went 20 more or less meters away till my ground control software announced out of signal,but with a lot of noise according to rssi meter.I had a very little problem in changing baud rate for my FY21AP,needed a little reading...The stock whip antennas are not 900 mhz exactly or...they need to be tuned,or change them with an inverted vee dipole for perfect signal range and noise levels.Very happy for this 3dr clone.Ready to buy the 433mhz version!

Got it less then 10 days shipping in Canada !. The connection cable is made for APM 2.5 only, it must be modified for APM 2.0 witch has different connector. Same product as 3DR but lot cheaper.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Got it less then 10 days shipping in Canada !. The connection cable is made for APM 2.5 only, it must be modified for APM 2.0 witch has different connector. Same product as 3DR but lot cheaper.

hobbyking can not get this item about 2 month and i will cancel my order

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

hobbyking can not get this item about 2 month and i will cancel my order

Muy bueno para fpv, parece buena calidad, a probarla ahora....

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Muy bueno para fpv, parece buena calidad, a probarla ahora....

A little difficult to get them up and running, but with perseverance your diligence is rewarded with a excellent wireless connection between your multiwii and PC.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

A little difficult to get them up and running, but with perseverance your diligence is rewarded with a excellent wireless connection between your multiwii and PC.

I have this up and running fine with APM2.5 and Mission Planner GCS. Pretty much zero config... just make sure you have the baud rate set to 57k. It will time out at other rates and appear broken.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I have this up and running fine with APM2.5 and Mission Planner GCS. Pretty much zero config... just make sure you have the baud rate set to 57k. It will time out at other rates and appear broken.

  1. 1
  2. 2
Customer files
Manual módulo HM-TRP Download [318]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!