S'inscrire

Product Finder

Options

Useful links

Discussion en temps réel
 
[["US","AU","GB","DE"]]
S'inscrire

H-roi Turning Trix MX2 1920mm EP 3D (ARF)

H-roi Turning Trix MX2 1920mm EP 3D (ARF)

Discontinued Product

Please continue searching for a similar product.
Rating:
Stock:
OUT OF STOCK
Poids
1 g
SKU:
MX21900EP
Description
du
Turning Trix vous offre une expérience 3D sauvage, c'est un avion de taille de gaz 30cc conçu et construit exclusivement pour l'énergie électrique, il a été conçu ultra léger, vous donnant un rapport poussée / poids massive avec le Turnigy motopropulseur recommandé.

Turning Trix a une belle qualité de construction, il a été bien pensé pour l'énergie électrique, ce n'est pas simplement une gasser avec une étiquette EP collé dessus! Poids en vol sera le même si au moins une taille gasser équivalent et avec le reccomended Turnigy Rotomax 1.60 installé, vous allez avoir le pouvoir potentiellement 3kw propre pour une puissance incroyable de poids, sans parler de la poussée d'un 21 "prop up avant! les deux ailes et les stabilisateurs horizontaux sont enfichables et toutes les surfaces de contrôle sont la broche articulée. les alliages boulons atterrisseur forts en plaques en alliage de le renforcer pour la durabilité et le matériel utilise billes liées, tringles lourds et puissants mais légers guignols en fibre de verre. la palette de couleurs est wow, et idéal pour l'orientation, la couverture a été savamment appliquée Tournage Trix est fini par un brillant glassfibre capot et roue pantalons peints.

Alors qu'est-ce qu'elle aime quand vous demandez pour les affaires 3D? Turning Trix monte à l'occasion, la combinaison de la puissance énorme, poids léger, de grandes surfaces de contrôle et de précision cellule vous donne une expérience 3D de grande classe, Tournage Tricks peut-être un peu pas cher à l'achat mais vous serez surpris par le nombre de maeuvers supplémentaire qu'elle jette lorsque demandé gentiment!

Caractéristiques:
construction ultra légère
Branchez ailes et stabilisateur horizontal
schéma de couleurs incroyable, parfait pour l'orientation
matériel de haute qualité
Superbe capacité 3D
robuste en alliage sous-chariot et montage
Broche articulée surfaces de commande

Spécifications:
Envergure: 1920mm
Longueur: 1736mm (sans spinner)
Wing Zone: 58.886dm2
Poids à sec: 2743g
Voler Poids: 4300g ~ 4700g

A besoin:
Votre propre 6 canaux TX / RX
Turnigy Rotomax 1,60 Brushless Outrunner
Turnigy DLUX 120A HV OPTO ESC
UBEC / régulateur
5 x MG numérique couple élevé servo
4000mAh 4500mAh ~ Nanotech 10s Lipoly
75mm spinner
Product
Specifications

Informations supplémentaires

  • Référence:
    MX21900EP
  • Brand:
    Non
  • Capacité ( mAh )
    Non
  • Poids (g)
    6830.00
  • Longueur:
    1480.00
  • Largeur:
    320.00
  • Taille
    490.00
Community
Discussions
Rate&
Review

Écrivez votre propre avis

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
As others have said, not quite up to EF or Sebby's quality, but not far off. I have 10S x 5000 Zippy Compacts in mine and the plane does "feel" a little heavy in the air, I might try some lighter batteries, but with Rotomax 160 and YEP120 ESC the performance is good at around 70 Amps max. Still experimenting with balance point - plenty of room for movement here. Great looker and all in all a really good 1000 performance model for less than 500 all up! Very happy customer!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
un tout petit prix et disponible pres de chez moi, j'ai pas su resister surtout qu'un moteur electrique et quelques lipo trainent dans l'atelier pour la hors saison de concours F3A. je recycle mes lipo dans l'accro ;) bref l'avion est bien plus beau en vrai que sur photo (etant deja joli) la "pin-up" est un atout
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Das Flugzeug lie sich sehr leicht und schnell fertigstellen .
Ich verwende ein 12S Setup eher fr eine Rennmaschine^^
Das Flugbild ist sehr schn und ausgewogen .

Ich empfehle jedoch das Steckungsrohr im Rumpf zustzlich in der Rumpfmitte zu befestigen um ein ausreien aus der Rumpfwand zu verhindern !
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Nice 3d airplane, very light and smart in 6s setup, here there is a maiden flight:
http://www.youtube.com/watch?v=vrQyaJsuKV0
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I just received mine today .. one word "AWESOME". Paint looks great, everything present, I am glad I bought this. I do wish the "distructions" came with it. Oh well .. I'll put it together. The big question .. electric or gas ... hummmm. Leanning towards electric. Thanks Hobbyking
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Quality is not quite up there with extreme flight or Sebart but then it's a fraction of their prices! Flight performance is is good, very neutral with very little coupling in knife edge, flys 'light' for sure. Good value for money.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
While after purchasing this mx it does look as nice as it does on hk site but it come with no instructions , no c of g, and nothing to hold the canopy down ? So you have to fit something up yourself ? Having said that it comes with good hinges and hardware set ,
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Finally completed the build, to my satisfaction.
Fixed the poor canopy fit by removing material from both ends of the canopy frame and fuse. I used an aluminium canopy latch to fix the canopy at the rear. I replaced the off centre wheels with Du-Bro hollow rubber ones with a similar diameter. The L.H. wing root required a 4mm balsa wedge added to the rear third to fit the fuse without a gap. I added fixing points rearward of the wing spar tray to fit a single rudder servo tray with ball raced C/F control arms and pull / pull cables to fabricated C/F rudder control horns with 102mm centres (to match forward arm dim's) spacing was 830mm.
I fabricated 4 motor stand-off posts with M4 fixings to suit the Rotomax 1.60 fitted. I also used HD alloy servo arms on all servos.
Ready to fly weight is 5.65kg with 2 x 4000mah 5S 25C LiPo's and C.G. measured as 55mm from L.E. at the wing tips. This is with no ballast added other than a 6mm neoprene pad added to the rear of the firewall for battery protection against motor fixing bolt heads.
Control throws are set as per the manual I've added under the files tab. (The manual was copied from the British Warehouse site)
Looking forward to the test flying phase, soon..................
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
This is undoubtedly in my opinion one of the very best planes that HK sell, the fuselage is very long its exactly the same length as a Wind 110 and it flies like it too. It tracks as straight as an arrow and carves beautiful arcs in the sky just like a pattern plane should but with those huge ailerons and elevator its more than capable of 3D. Because it really was built for electric its also very light and for this money a steal. Ive had mine a year now and it must have 100 plus flights on it and absolutely nothing has broken, fallen off, failed or gone wrong. Personally I wouldnt put the recommended (here) Rotormax motor in it I have the SK3 5065 320 KV in mine turning an 18 X 10 prop on ten cells through a K Force Esc and its perfect. The SK3 is much lighter (over 300gms) and less than half the price, also (because of its shape) its a much better fit in the plane. Cant recommend this airframe enough but leave the stickers off, get some black tinted paint and spray the instead of the canopy and this is a pure and beautiful MX2.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Postage $13.99 with 3 day turnaround from the HK Aus Warehouse.
The kit was double boxed, and arrived intact, well done HK.
The kit itself is large, no instructions are supplied, hardware is seperately bagged and is basic. 4mm Landing gear bolts are missing, wheel hubs are drilled off centre rendering them useless, cowling paintwork is poor with raised paint edges due to edge masking & paint bleed across colours. Canopy does not fit fuse and will require frame trimming to fit, no latching for canopy is supplied. Covering will need rework around vertical stab. Aluminium landing gear will need ends trimmed 12mm to fit wheel spats properly, wheel axil's appear inadequate for a 5kg aircraft. Wing & stab main spars are thin wall aluminium tube & seem too short. Hinging is flat plastic pinned variety. I will fit Turnigy Rotomax 1.60 outrunner, dlux 120A HV opto ESC, dlux 10A HV SBEC, ultra light 20 x 12" wood propeller, 75mm carbon spinner, digital servos are 3 x HXT 10kg & 2 x 4.8kg mini's on stab. I will convert rudder to pull/pull using 0.8 coated wire cables. Batteries are 2 x Zippy compact 4000mAh 25C 5S Li-Po @ 460gr each. I'll report again when it's all together & tested......
verified_user Quality
trending_up Value
playlist_add_check Overall
View all reviews
Upload
Videos
  • H-king Turning Trix MX2 1920mm EP 3D

Upload video
Upload
Files

Seuls les utilisateurs identifiés peuvent télécharger les fichiers. Merci de vous connecter ou de vous enregistrer pour commencer à aider les autres membres dès aujourd'hui!

Étiquettes des produits

Utiliser des espaces pour séparer les étiquettes. Utilisez des apostrophes pour les phrases.