Afficher : TOUTES CATÉGORIES 0 Modèles volants 1952 Avions 1114 Avions 147

HobbyKing Edge 540 V3 (Rouge / Blanc) 1200mm 3D (ARF)

HobbyKing Edge 540 V3 (Rouge / Blanc) 1200mm 3D (ARF)

22 La Revue

Prix:

Now save économisez 0,00 € 0,00 €

148,29 €

Déjà acheté Discontinued Product

Please continue searching for a similar product.

SKU:

049000003

Livraison gratuite? Cliquez ici pour apprendre plus!

Partagez ce produit et gagner 800 points (7,41 €) [ ? ]

Description du produit

Le Edge 540 V3 doit être l'un des meilleurs à la recherche des avions de course et performances jamais construit, mais ne vous méprenez pas, le HobbyKing Edge a été conçu avec une chose à l'esprit, voltige 3D extrêmes!

La qualité de ce bord est tout aussi bon qu'il obtient, la cellule a été construit pour maintenir le poids de vol minimal mais assez fort pour prendre la peine de voltige extrêmes, la superbe couverture de qualité a été savamment appliquée et pour la touche finale, le capot, canopée et roue pantalons sont finis dans une peinture brillante profonde. Le matériel est excellent et également choisi de garder le poids de vol à un minimum absolu et bien sûr le modèle caractéristiques prise dans le tube d'aile et CF que vous attendez pour un transport facile.

Les H-King Edge 540 V3 effectue chaque pouce aussi bon qu'il semble, naturaly il fait un grand plan de sport, mais il serait juste de dire que le hardcore 3D est ce que l'Edge a été conçu pour. La précision de la cellule, superbe allure, caractéristiques de qualité supérieure de la ligne et le poids plume étonnante faire le Edge 540 V3 l'incontournable plan pour tous les pilotes de voltige et 3D!

Caractéristiques:
regards étonnants
construction de qualité supérieure et revêtement
Facile et rapide à construire
poids ultra léger mais solide cellule
Superbement fini
Superbe capacité 3D
assemblage sur site rapide, facile à transporter

Spécifications:
Envergure: 1200mm
Longueur: 1180mm
Wing Zone: 28.9dm2
Poids à sec: 729g (inc tout le matériel)
Voler Poids: 1300g ~ 1500g (environ)

A besoin:
Votre propre 4 ~ 6 canaux TX / RX
35mm Brushless Outrunner Motor
40A ~ 50A ESC
4 x Digital High Torque 9g ~ 12g servo
Batterie 2200mAh ~ 3300mAh 3s Lipoly
50mm Spinner
UBEC (Facultatif)

Spécifications du produit

Vidéos

Télécharger une video

Inscrivez-vous pour télécharger des vidéos, s'il vous plaît se connecter ou s'inscrire

Discuter 0

Sujets

Trier par

Sujets les plus récents

Publier un nouveau sujet

La Revue

Inscrivez-vous pour écrire des critiques, s'il vous plaît se connecter ou s'inscrire

Phillip | Acheteur vérifié

Overall
Quality
Value

Customer Rated

Jun 28, 2015

Fatal Flaw....
This airplane flies really good BUT the horizontal stabilizer has lightening holes drilled in the center. It is also constructed with 2 halves (right and left) with a perpendicular glue joint right in the middle. It will break in the middle and cause a severe crash. It is just poorly designed and will fail. It just happened to me today. In order to eliminate this structural design flaw. throw away the stab that comes with it and make a new one from a single piece of 3/16' balsa. Cut slots of hinges and hinge the elevator. HobbyKing should make this modification immediately as it is one very good flying airplane if you can keep the stabilizer in one piece!

Samanafatta | Acheteur vérifié

Overall
Quality
Value

Certified Buyer Rated

Jan 26, 2015

perfct plane very nice flight Amazing 3d experience very very very good

msabalbal | Acheteur vérifié

Overall
Quality
Value

Customer Rated

Dec 16, 2014

Excellent model, Beautiful and responsive. I used Motor PropDrive 3542-1000KV with ESC HobbyKing 50A and Prop APC 12x6E, Please refer to my YouTube published at:
http://youtu.be/s50XCFsyeBo
Thank you HobbyKing.

ffinybryn | Acheteur vérifié

Overall
Quality
Value

Customer Rated

Sep 09, 2014

Not happy. Yes, the plane looks nice and everything, but after less than two minutes of flying, whilst still trimming out, the right hand rear horizontal stabiliser completely snapped off taking the RH elevator with it. Luckily, I was able to make an emergency landing with minimal damage to the undercarraige. However, this may not have been possible had I been performing a 3D manoeuvre such as the plane is advertised! On inspection, the rear stabiliser is constructed of lightweight balsa (as is the rest of the plane) with the woodgrain running in line with the fuselage. It was an accident waiting to happen. Other purchasers have had exactly the same experience and Hobbyking has failed to address the issue. Looks great. But as a "plane" it fails. As a 3D plane it has a serious design flaw and is not fit for purpose. "Quality as good as it gets" does not instill much confidence for further purchases.

ralph | Acheteur vérifié

Overall
Quality
Value

Customer Rated

Aug 17, 2014

top airplane & good value . Had 4 good fly's just the covering coming off in 1 spot my set up is e-flit 15 brushless outrunner Dualsky xc 60 amp emp , 11.7" emp prop & trningy 3s 2200 the setup is a little over kill but can be used in a bigger plan down the track . Flying around 1/2 throttle about 10 minute's no heat at all if you are mad you could go for a 12.7 " prop have fun

Trevor | Acheteur vérifié

Overall
Quality
Value

Customer Rated

Jun 21, 2014

I bought this and collected it from the UK warehouse, to fit my GPS unit to. Didn't read other reviews, consequently on the first turn into wind on a windy day the RHS tail-plane c/w elevator fluttered to the ground ! I managed to land it with no other damage, don't know how! Fitted the complete tail-plane ass'y from my old Yak and braced it up with closed-loop wire. Never looked back, except for the papier-mache tail-plane this is a superb model. I did also put lots of epoxy round the undercarriage plate and firewall, it is an ARF after all!

Wojtek :) | Acheteur vérifié

Overall
Quality
Value

Customer Rated

Feb 11, 2014

A very good aircraft. Good lightweight and strong airframe. My Edge 540 take of weight is 1400g on the spot with 3542 size 1000 kv, 55A ESC and 3200mAh 3s lipo.
Reinforcement of the elevator recommended with 3mm carbon strip. Also Crimp tubes were missing in my edge, so get those just in case.
CG just 10mm behind carbon spar gives good 3D flying experience.

jetson3000 | Acheteur vérifié

Overall
Quality
Value

Customer Rated

Jan 17, 2014

This version is discounted because the colored shrink film is defective.
Mine arrived with several issues on colored shrink film that peels off
See also thies review:http://www.rcgroups.com/forums/showthread.php?t=1584272&page=17

Richard | Acheteur vérifié

Overall
Quality
Value

Customer Rated

Jan 14, 2014

An beautiful plane. Superb quality finish. Well packed. Amazing value.

I have not yet flown it as am waiting for some minor parts but will need to handle the controls with extreme caution as this plane has huge control surfaces - scary.

baytacoglu | Acheteur vérifié

Overall
Quality
Value

Customer Rated

Dec 20, 2013

It is absultely very easy to assemble. Can be flight ready in just 4-6 h. The control surfaces are big but the supplied cyano hinges are very small so I had to change them with bigger ones. The control horns according to me are not trusworthy so I changed the control horns as well. Servo spaces are not for mini servos but for micros only so if you want to use more powerful ones you will have some trouble to open more space for a mini servo.
The workmanship is of decent quality and the plane is very light weighted.