La pente HobbyKing ™ Guppy Mini est un brillant modèle parfait pour ceux qui cherchent à entrer dans les planeurs de pente, sans les tracas et les frais de construction d'un kit traditionnel! De petite taille, une excellente qualité de construction et un niveau élevé de pré-assemblage, le tout à un prix qui ne peut pas être battu! Travailler avec le designer européen Mitja Erman, le Guppy a été affinée dans un modèle de pente grande dans un bouchon et la version vol pour vous rendre à la pente juste que beaucoup plus rapide.
L'aile en deux parties est construit à partir de balsa et recouvert de film ultra-léger, comme le fuselage, stab horizontal et vertical. Un cône de nez en plastique peut être retiré permettant une conversion facile à l'énergie électrique.
La pente HobbyKing ™ Guppy Mini arrive avec les sections ailes, fuselage et la queue pré-assemblés, ainsi que les servos, tringles et guignols tous les pré-équipés. Après l'ouverture de la boîte, vous aurez simplement besoin de boulonner sur l'aile, le stab horizontal et installer votre propre récepteur / batterie. Voler littéralement minutes après l'ouverture de la boîte.
• Plug and Fly - il suffit d'ajouter le récepteur, la batterie et voler!
• Construit en balsa et contreplaqué cellule avec flèche de tube de carbone
• Pré-couvert en poids léger film plastique multicolore
• Bolt ensemble construction, pas de colle nécessaire
• Servos, tringles et guignols pré-équipé
• Conception de la pente ou peut être convertie en énergie électrique
Wing Zone: 13.4dm²
Airframe Poids: 180g
Servo: 2 x 9g micro
2+ émetteur et le récepteur CH (micro récepteur recommandé)
4,8 ~ batterie de récepteur 6V
UBEC régulateur / tension (si vous utilisez 2S batterie de récepteur LiPoly)
Motorsize ( diam ou cc )
Envergure ( mm ):
SaleWeight ( g),
Cadre / PNF / RTF ( mm )
IC / 2 : Elec:
BEWARE These have an extremely dodgy elevator push rod setup. They have used 2 different gauge wires and joined them by the servo with heat shrink and they fail. The outer guide for the push rod is glued in during construction and cannot be replaced. Sounds a simple fix but believe me it is not Pity as apart from that they are nicely built.So after reinforcing like everyone has said, reattach the tail to the boom with epoxy, solder the elevator push rod to z-bend, and add balsa back stop behind wing, the plane lasted all of 30 min. Throwing javelin style, landing in 2 inch grass, the sheeting on the right wing has failed, between the first and second wing rib. Thankfully I noticed it before my next throw, but now I am faced with uncovering and resheeting that section and praying there isn't anything else broken on this "pnp" model. Perhaps it is rtf, rebuild to fly?
After waiting weeks it's finally in the UK warehouse, Got mine and it's a lovely glider but have to comment on the way the elevator control rod is connected to the servos, (2 pieces of wire joined by a piece of heat shrink tubing) are you joking or what HK, as soon as i powered up the elevator servo the joint came apart, in the air i would have more than likely lost what is a very good glider! But easy fix with electric guitar string (see my photos in files tab) apart from that it's a very well made little slope soarer. Also spent 10mins going over it with my iron as a few lose bits of film, 35gram added plus 2 300mah 2cells to get c of g right.I wanted a small fast glider and this looked perfect. I paid full price which was quite expensive for a small simple model but it looked good and was exactly what I wanted. It was delivered well packed no problems and looked good. Before I even got it in the air, the elevator push rod close to the servo came apart. The 2 pieces of wire in the elevator push rod had been joined with heat shrink close to the servo. This is a very crappy way to may this critical joint. I fixed this by soldering the two pieces of wire together. Then the whole tail assembly came unstuck from the carbon fibre tail boom. I glued this back with epoxy. Both of these failures would have potentially destroyed the plane if it had been in the air. While doing the repairs, the nut that the wing bolt screws into fell off inside the fuse. I had to hack a hole in the side of the fuse to replace this. This is a great little plane manufactured to a shameful standard. I will never buy another ARF plane from HobbyKing.Haven't actually got to fly mine yet, but thought I would share what I have observed so far.
i) it's a lovely design & well made for the price.
ii) you only get 1 servo to control the ailerons, but a bit of research on rcgroups shows how to convert to 2.
iii) the designer recommends you tape the wings together to stop them getting ripped off in a crash & breaking the mounting points. I would go one step further & suggest you glue the 2 halves together & to the fuselage.
iv) the biggest issue I see is the ailerons are taped to the wing on the wrong side (imho) as it restricts the movement on the up side, but unrestricted going down - which is the opposite of what you want for clean rolls. So I am expecting poor handling because of this & there's no way to get the tape off without damaging the covering. The only other way to solve it would be to flip/swap the wings & remove/refit the control horns.wing fixing screws are odd size about 2.7mm diameter thankfully I have found two metal ones in my scrap box!
Nose cone is flimsy!
Needs 40-50gms to balance ( model is only 200 with receiver an battery)
Test glide fine, apart from nose cone!Arrived late god bless Parcelforce! looks fine but....
1. wing fixing screws strip when tightened
2. elevator pushrod is too long for correct adjustment
3. Aileron clevis poor quality
4. Attaching cockpit with 3 scraps of masking tape is a bit naff to say the least
It will also need lead to balance as a glider unless you fit a large battery!
With a little care could be a great product, please try harder.
Now I must try and find some wing screws.Nice sailplane, all in all sturdy, but limited quality at best. Needs reworking. Crappy one servo-ailerons solution. Will rework it to to servos. The tail came loose on the first flight, absolutely have to check and reglue those. As a sailplane, it needs much ballast up front when working with a light battery.
Took me more than an hour to overcome the build defect on one aileron (not enough deflection due to wood not worked properly).This plane need some work. But you get a great sloper for the bucks!!
1. Make sure the Tail is correct glue on the tail boom
2. Change the Single flaps servo to 2 micros servos. You can use now flaperons/brake and mybe Thermik mode.NOW I AM GOING THRU THE WHOLE THING. FOUND THE FRONT FORMER THAT HOLDS THE WING ON HAD NO GLUE. THE CANOPY DOES NOT FIT - NEEDS TRIMMING. NEEDS A VERY LIGHT BATTERY TO GET CG. THE NOSE CONE IS VERY FLIMSY PLUS MINE HAD NO GLUE AND WAS CRACKED RIGHT OUT OF THE BOX. THE SERVOS LOOK CHEAP. SORRY I BOUGHT THIS THING. NOT MY FIRST BAD EXPERIENCE WITH HOBBYKING SO I THINK I AM DONE WITH THEM.
No File Name Télécharger maintenant [143kb] No File Name Télécharger maintenant [261kb] No File Name Télécharger maintenant [261kb] No File Name Télécharger maintenant [262kb] No File Name Télécharger maintenant [205kb] No File Name Télécharger maintenant [403kb] Week link of the elevator control Télécharger maintenant [2871kb] new elevator control using guitar string Télécharger maintenant [3322kb] whats inside the tail Télécharger maintenant [3615kb]