Devenez fournisseur Blog Nouveaux articles
S'inscrire

Prix total

0,00 €

Panier 0 Panier 0 Loading...

Système d'alimentation Micro w / GPS-7 Boîte de vitesses

Generating Links

Système d'alimentation Micro w / GPS-7 Boîte de vitesses

Prix:

Now save économisez 0,00 € 0,00 €

8,71 €
Déjà acheté Discontinued Product

Please continue searching for a similar product.
SKU:
GPS7
Livraison gratuite? Cliquez ici pour apprendre plus!
Micro brossé système d'alimentation pour les voyageurs d'intérieur.
Caractéristiques:
Type: Brossé
Dimension: 16 x 7mm
Longueur de l' arbre: 5mm
Diamètre de l' arbre: 1mm
Poids: 3.3g
Courant max: 1.8A
RPM: 3V / 40,000rpm à vide
Prop suggérée: GWS 4530
Données de test;
Prop: GWS 5030
Tension: 3.3, 3.8, 4V
Courant: 0,76, 0,89, 0.93A
Watts: 2.508, 3.382, 3.72W
Poussée: 31, 36, 38g
Efficacité (g / m): 12,36, 10,64, 10,22
Prop: GWS 4530
Voltage: 3,8, 4V
Courant: 0,81, 0.87A
Watts: 3.078, 3.48W
Poussée: 32, 35g
Efficacité (g / m): 10,40, 10,06
attributeset-10
Close

Dimension Diagram Guide

  • attributeset-10

Close

Télécharger une video

Inscrivez-vous pour télécharger des vidéos, s'il vous plaît se connecter ou s'inscrire

Sujets
Trier par
Sujets les plus récents
* Surnom:

* Votre réponse:


Veuillez saisir le texte affiché dans l'image dans le champ ci-dessous
*Code de vérification:
Annuler
Soumettre
Publier un nouveau sujet
* Surnom:

* Votre sujet:



Veuillez saisir le texte affiché dans l'image dans le champ ci-dessous
*Code de vérification:
Sujet du message

Inscrivez-vous pour écrire des critiques, s'il vous plaît se connecter ou s'inscrire

| Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Jun 18, 2013

Is used for electronically reversible radar screen

crafter | Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Apr 22, 2012

I got two of these, and they weigh an average of 3.575g out of the packet. The prop shaft extends 18.5mm beyond the front face of the large gear. The prop bushing at the tip of the shaft is 7mm deep and has a 4mm diameter. GWS props with a 4mm ID prop hubs will press-fit nicely onto these. Both my units came with their main shafts feeling rather tight to rotate by hand. I connected the motor to a variable DC power source and powered them with 1V, slowly increasing it to 3V. Initially the no-load

current draw was 400mA. Left to run for about a minute like this, you can hear the revs go up, and eventually the no-load current was only 100mA. After that, the main shaft felt very easy to rotate by hand, it was no longer tight. I think the retaining bushing was pressed on too tight, but the above method was able to break-in both my units.

| Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Aug 22, 2011

Nice and light motor/gearbox combo. While the power output with a GWS 5x3 is a bit less than stated it works well in my micro aircraft with a 130mAh 1S battery and the HK brushed micro ESC. The propeller fits well on the shaft adapter, but care must be taken to not bend the tiny shaft.

Client | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

May 23, 2011

I like it! I am flying a 20g depron/mylar, rudder/elevator model using a gws 5x3 prop and a nanotech 130mAh cell and a vapor brick. Cruises on 1/2 power with excellent duration. Probably unsuitable for 3D?

Steve

Xordarion | Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

May 11, 2010

Wonderful thing!

I added this to my Kyosho Minium 4 Ch, which was a bit underpowered right out of the box. I added a GWS EP Propeller (DD-5030 127x76mm) and now the plane works quite fine!

Client | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Mar 23, 2010

The small diameter (1 mm) is soft and very easily bent. That said, use of a homemade propsaver aids greatly. For the cost, a viable Indoor sport motor for my 21.5 gr. AUW foamies.

Riggers | Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Mar 03, 2010

Much smoother than the 6mm unit but why the long shaft ? The prop adapter is very eccentric making the prop run way out of true. weight 3.3grams

drrk24 | Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Feb 07, 2010



"You might find further reviews (displaced by s/w malfunction) on:



http://www.hobbyking.com/hobbycity/store/product_reviews.asp?idproduct=1000#review"



| Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Nov 13, 2009

The perfect parkzone replacement

Téléverser un fichier

Inscrivez-vous pour télécharger des fichiers.
S'il vous plaît se connecter ou s'inscrire pour commencer à aider les amateurs maintenant!

Accessoires