New Items Forum
S'inscrire

Total Price

0,00 €

Panier 0 Panier 0 Loading...

Contrôleur de vol MultiWii SE V2.0 w / FTDI

Contrôleur de vol MultiWii SE V2.0 w / FTDI

Discontinued Product

Please continue searching for a similar product.
SKU:
381000133
WANT FREE SHIPPING? Click here to find out more!

La V2.0 MultiWii S'est un / contrôleur de vol de l'accéléromètre à base de gyroscope qui est chargé avec des fonctionnalités. Avec des options d'évolutivité et de la pleine programmabilité, cet appareil peut contrôler à peu près tout type d'aéronef. Ceci est le contrôleur de vol idéal pour votre avion multi-rotor.

Caractéristiques:
• Petite taille, 35x35mm trous de montage
• 6 canaux d'entrée pour récepteur standard et le récepteur PPM SUM
• Jusqu'à la sortie du moteur 8 axes
sortie • 2 servos pour PITCH et ROLL Cardan système
• Peut utiliser la sortie d'un servo pour déclencher un bouton de la caméra
• prise TTL FTDI / UART pour le débogage, télécharger le firmware ou l'écran LCD
• Prise de I2C pour étendre capteur, I2C LCD / écran OLED ou CRIUS I2C-GPS NAV conseil
• régulateur de tension 5V LDO 3.3V séparée et
• ATMega 328P Microcontroller
• MPU6050 6 axes gyro / accéléromètre avec unité de traitement de mouvement
• HMC5883L 3 axes de magnétomètre numérique
• Capteur de pression numérique BMP085
• A bord convertisseur de niveau logique

Mode avion:
• l'un des modes de base suivants
- Acro
- Niveau
- Alt Maintenez
- Verrouiller Head
• Mode en option
- Headfree (CareFree)
- Hold GPS (Besoin récepteur GPS + I2C-GPS Conseil NAV)
- GPS Retour à la position de la maison (Besoin récepteur GPS + I2C-GPS Conseil NAV)

Spécifications:
Dimension: 40x12x40mm
Poids: 9.6g
Fixation espacement des trous: 35 mm (Il peut être modifié à 45mm par le Conseil CRIUS de distribution)
Diamètre du trou: 3mm

Le contenu de la boîte:
MultiWii SE FC x 1
(Câble Mini USB requis, mais vendu séparément) de la carte x 1 programme USB
3Pin câble 1Pinx3 100mm x 2
3Pin câble 3Pin 100mm x 1


Plus d'informations peuvent être trouvées sur le site Web MultiWii.
http://www.multiwii.com

  • UGS 381000133
  • Brand -
  • Capacité ( mAh ) -
  • Poids 30.0000
  • Longueur 130.00
  • Packaging Width 10.00
  • la taille 90.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Never Buy it from them. they will send you

XZN MWC MultiWii SE Standard multi-Copter 4-axis Main flight con

http://www.geeetech.com/xzn-mwc-multiwii-se-standard-multicopter-4axis-main-flight-con-p-552.html

this board which is very poor and cheaper(US 19) than the item shows in their listing.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Never Buy it from them. they will send you

XZN MWC MultiWii SE Standard multi-Copter 4-axis Main flight con

http://www.geeetech.com/xzn-mwc-multiwii-se-standard-multicopter-4axis-main-flight-con-p-552.html

this board which is very poor and cheaper(US 19) than the item shows in their listing.

They sent me the wrong board the 1st time. Did a RMA to replace wrong board and they sent me the same wrong board again. Can't comment on functionality because I've never received what I ordered!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

They sent me the wrong board the 1st time. Did a RMA to replace wrong board and they sent me the same wrong board again. Can't comment on functionality because I've never received what I ordered!

Good board for my 20 cm. arm small tricopter flying great with D2822/17 kv 1100 motor and 1,5 Ah lipo pack for about 10 minutes of very fun.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Good board for my 20 cm. arm small tricopter flying great with D2822/17 kv 1100 motor and 1,5 Ah lipo pack for about 10 minutes of very fun.

Hi All! I've got MultiWii 2.0 installed and running on my Quadro. HobbiKing Rx, HobbiKing 10A ESCs are used. Previously I used HobbyKing Multi-Rotor Control Board and it flied well. On this MultiWii control motors running not fast enough to take quadro off the ground. Even if I move throttle stick to the most up position it does not fly. Can anyone say what is wrong?

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Hi All! I've got MultiWii 2.0 installed and running on my Quadro. HobbiKing Rx, HobbiKing 10A ESCs are used. Previously I used HobbyKing Multi-Rotor Control Board and it flied well. On this MultiWii control motors running not fast enough to take quadro off the ground. Even if I move throttle stick to the most up position it does not fly. Can anyone say what is wrong?

Nice board flying very well But when I tried to plug the battery monitor on A3 input as shown on file "pin assignments" (lipo directly on this input) I burn the Atmega ...I had to add the divider resistor before input the direct lipo voltage.So be carefull bfore wiring this batterie monitor input (A3 pin).
I put a updated picture of the pin assignments with the rsistors in the file section

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Nice board flying very well But when I tried to plug the battery monitor on A3 input as shown on file "pin assignments" (lipo directly on this input) I burn the Atmega ...I had to add the divider resistor before input the direct lipo voltage.So be carefull bfore wiring this batterie monitor input (A3 pin).
I put a updated picture of the pin assignments with the rsistors in the file section

I use this board on a 55cm quad, replacing a homemade combo of Arduino ProMini and 4 single sensors boards... Adding a LZ-GPS was very easy because I2C is brought out on its own pin header. The HK S2 V2 board has the Crius V2 layout and comes with preloaded MultiWii 2.1 firmware for Quad X constellation. Firmware can easily be updated or changed to any other config with the FTDI header and Arduino 1.01 software. The MPU 6050 gyro/acc gives really great and stable flight behaviour with an very smooth ACC level mode never seen before. BMP baro is not state of the art anymore (low resolution), but its OK to get a height hold mode within 2-3 meters. Overall: Great board with good quality, small boards size, totally worth the money. Will buy a 2nd one for my Flydumini as soon as they are on stock again.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I use this board on a 55cm quad, replacing a homemade combo of Arduino ProMini and 4 single sensors boards... Adding a LZ-GPS was very easy because I2C is brought out on its own pin header. The HK S2 V2 board has the Crius V2 layout and comes with preloaded MultiWii 2.1 firmware for Quad X constellation. Firmware can easily be updated or changed to any other config with the FTDI header and Arduino 1.01 software. The MPU 6050 gyro/acc gives really great and stable flight behaviour with an very smooth ACC level mode never seen before. BMP baro is not state of the art anymore (low resolution), but its OK to get a height hold mode within 2-3 meters. Overall: Great board with good quality, small boards size, totally worth the money. Will buy a 2nd one for my Flydumini as soon as they are on stock again.

A good product!!! This comes pre-programmed. But the PID values are all out of boundaries. So you will face a hard time setting it up...

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

A good product!!! This comes pre-programmed. But the PID values are all out of boundaries. So you will face a hard time setting it up...

bu gne kadar kullandm kartlar arasnda en iyisi.
gps modl de almanz tavsiye ederim.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

bu gne kadar kullandm kartlar arasnda en iyisi.
gps modl de almanz tavsiye ederim.

The ever expandable MultiWii controller

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

The ever expandable MultiWii controller

The 0.03 hectopascal maximum resolution of the BMP085 is an optimum enabling the sensor to respond to differences in altitude of 25 cm.



At this days pressure sensors have ~ 10cm. altitude sensitivity!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

The 0.03 hectopascal maximum resolution of the BMP085 is an optimum enabling the sensor to respond to differences in altitude of 25 cm.



At this days pressure sensors have ~ 10cm. altitude sensitivity!

  1. 1
  2. 2
Customer files
pin assignments Download [184]
No File Name Download [184]
Newbies Guide (By ATXHELI rev. 04/22/201 Download [452]
pin assignments with Batt monitor resist Download [199]
Flight-Ctrl ME 2.0 Schematic Download [781]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!