S'inscrire

Product Finder

Options

Useful links

Discussion en temps réel
 
[["US","AU","GB","DE"]]
S'inscrire
Shipped From:
  • USA

Servoless rétractable Landing Gear V2 - fixe ou 90 degrés de rotation (1 paire)

Servoless rétractable Landing Gear V2 - fixe ou 90 degrés de rotation (1 paire)

Discontinued Product

Please continue searching for a similar product.
Rating:
Stock:
OUT OF STOCK
Poids
200 g
SKU:
189000015
Description
du

La meilleure façon de mettre escamote dans votre avion. Pas besoin d'installer un boîtier de commande, câblage désordre ou d'un système d'air compliqué. Vissez dans les escamote, se connecter à votre Rx et vous êtes prêt!
servo-mécanisme fiable avec engrenages en métal et un moteur à couple élevé assure le vol sans problème!
Pourquoi se préoccuper de systèmes d'air quand vous pouvez maintenant avoir une unité électrique réaliste et fiable à une fraction du prix ?!

Caractéristiques:
3 secondes sur la protection actuelle et le brouillage
Comprend raccord à tordre la jambe de force 90 degrés lorsqu'il est rétracté
circuit intelligent maintient l'unité rétractée même si vous connectez le pouvoir. Seul le signal de l'émetteur peut prolonger ou rentrer le train.

Spec.
Tension de fonctionnement: 4.8 ~ 6.0V
Courant de fonctionnement: 0.1 ~ 0.3A (3 secondes sur la protection actuelle)
Rentrez Chargement: 60g
Wire Leg: 3mm
Ne convient pas pour un avion plus lourd que 2,5 kg

Product
Specifications

Informations supplémentaires

  • Référence:
    189000015
  • Brand:
    Non communiqué
  • Poids (g)
    200.00
  • Longueur
    250.00
  • Largeur:
    50.00
  • Taille:
    97.00
Community
Discussions
Rate&
Review

Écrivez votre propre avis

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
Great product for the money just look like eflite retracts but half the cost these will fit straight into my parkzone spitfire also avery very quick delivery well done hobby king.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Super Einziehfahrwerk, passt in die Parzone-Flieger (Spitfire, P47). Nur leichte Anpassungen ntig. Leider sind keine Achsen dabei, hier empfielt es sich, die Originale von e-Flite einzusetzen
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Koupil jsem dva kusy a oba dva pestaly fungovat jet na zemi. Pinou je patn materil, zvit se hned sjede!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Der erste Eindruck dieses Fahrwerks wahr sehr erfreulich. Doch leider nach 5 maligem ein und ausfahren ohne jegliche Last, wirklich nur auf dem Tisch liegend, hat das eine Fahrwerk den Dienst aufgegeben. Ich konnte es nicht lassen das Teil zu ffnen um zu sehen was Sache ist. Es wahr einfach kein Gewinde mehr im Antriebs-Veriegelungsbolzen! Also der Kleber mit der Aufschrift "Przisionsteile" ist doch eher fragwrdig.
Ich werde dieses Produkt nicht zurcksenden, da ich nicht so lange warten will. Werde es selber reparieren.
Kaufen wrde ich es bestimmt nicht mehr. Schade, bin sonst sehr zufrieden mit HobbyKing
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Installed retracts on the new F4U-1A Corsair, mounts fit just fine but two screw holes had to be drilled, they were a few mm off, but that's not really a problem. The problem is that one of the retracts stopped working after testing them for a few minutes, glad I didn't take it in the air or else I'd probably have a major scuffed up wing... BUT before the one retract stopped working, the other one, the link to twist 90 degrees kept coming off, having a round piece over the ball doesn't work, it wears out really easy and starts popping off, they should've made something to actually hold it in place. Tomorrow I will go to my brother's mechanic shop and fashion something to keep it in place while it twists, but I have to wait for another shipment of retracts... Very poor quality but I'm still going to give it another shot so I can see how they perform while in the air and actually landing... Also ordered a few different type of retracts to see if any of those will work better... (Please HobbyKing, make metal links for the 90 degree twists! I can't trust small thin plastic pieces to keep my wheels straight, or else they're spinning all over the place!)
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Previous comments on here indicated that the V2 had metal trunions, they are made of plastic. They are held in position with grub screws into the plastic, this will still allow the legs to rotate on landing. Not happy at all. (probably the reason why all the previous comments have been removed from here as well), come on HK, a review is a review so lets here the good and bad points without censorship.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
The Trunions on these retracts are plastic, they are good gear, but I will return mine for the metal ones. The plastic will not be suitable for my application. I bought them because I thought they were replacing the changeSun purple retracts that had metal trunions. These are ChangeSun retracts, just cheaper ones. I guess V2 now means "made of plastic not metal"? I thought they were V2 because they now have 2 set screw holes.... A bit decieving?
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
They are recommended for the Mosquito by Hobbyking ,only they do not fit the plane .
verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
Upload video
Upload
Files

Seuls les utilisateurs identifiés peuvent télécharger les fichiers. Merci de vous connecter ou de vous enregistrer pour commencer à aider les autres membres dès aujourd'hui!

Customer files
retract_assembly Télécharger maintenant [1182kb]

Étiquettes des produits

Utiliser des espaces pour séparer les étiquettes. Utilisez des apostrophes pour les phrases.