S'inscrire

Product Finder

Options

Useful links

 
[["US","AU","GB","DE"]]
S'inscrire
Shipped From:
  • Global

SK450 Dead Cat "Défibrillateur" Power et A / V Distribution Board et Power Shield

SK450 Dead Cat "Défibrillateur" Power et A / V Distribution Board e...

QTY:

Now save enregistrer 0,00 € 0,00 €

21,71 €
Rating:
Stock:
Poids
463 g
SKU:
9171000236

Suggestion Box

Please let us know if you found any issues with this product listing.
We take our customer comments very seriously and in many cases our website modifications and product updates are a result of your comments!

Meilleur prix

HobbyKing s'engage à vous offrir les meilleurs prix. Si vous avez vu ce produit autre part pour moins cher, merci de nous le faire savoir!

Description
du

Nous avons retiré le défibrillateur et choqué un peu de vie sérieuse pour la conversion de Dead Cat! Le style Araignée Quad-Copter était déjà impressionnant avec son angle de bras optimisé et mise en page pour une vue FPV libre de l'hélice. Et maintenant, la progression très attendu à une puissance intégrée et la carte de distribution A / V et branchez puissance blindé.

Le nouveau conseil d'administration inférieur a des plots de soudure directes pour les lignes électriques moteur ESC droit à la base des bras et de la puissance "dans" pads situés directement au-dessus de la batterie pour réduire au minimum le câblage. Il y a connecteur d'alimentation de l'avant, arrière et centrale pour votre équipement de FPV et contrôleur de vol, tous liés à la protection de puissance qui sans effort fournir est un régulée, filtrée et RF Noise blindé 5 volts à un énorme 3 ampères pour le contrôleur de la caméra et vol 12 volts à 1 ampère pour les plus affamés des émetteurs vidéo. Les connecteurs vidéo à l'avant et à l'arrière également fournissent non seulement la tension, mais portent également le signal audio et vidéo de l'avant caméra montée à l'émetteur vidéo montée à l'arrière. Cette mise à jour vous permettra d'économiser du poids, nettoyer votre mise en page et d'améliorer la fiabilité en réduisant les échecs de connexion. Je suppose que ce Dead Cat a 9 vies après tout!

Caractéristiques:
• distribution d'énergie intégrée
• plots de soudure de style Wick
• émetteur intégré le câblage de l'appareil photo et la vidéo
entrée • 3 ou 4 cellules
• SMPS convertisseur avec le bruit RF bouclier de protection
• protection thermique

Spécifications:
Tension d'entrée: 8-16v (3-4 cellules LiPoly)
poids: 142g
Sortie: 5V / 3A et 12V / 1A

* Notez les morts conversion chat Défibrillateur pour le SK450 exige le cadre SK450 et conversion de chat mort liés ci - dessous.

Product
Specifications

Informations supplémentaires

  • Référence:
    9171000236
  • Brand:
    Non communiqué
  • Poids (g)
    463.00
  • Longueur
    375.00
  • Largeur:
    30.00
  • Taille:
    215.00
Community
Discussions
Rate&
Review

Écrivez votre propre avis

Only registered users can write reviews. Please, sign in or sign up

Quality
Value
Overall
I am completely happy with this, what a great product! This did wonders to clean my quad up! Some sort of schematic would have been nice however a quick check with my DVOM and I was off and running! This is a must have for the Deadcat frame!!!
Quality
Value
Overall
Quality
Value
Overall
great thing, saves a lot of cables

and makes it look cleaner
Quality
Value
Overall
Quality
Value
Overall
This is a must for your dead cat upgrade

making the whole upgrade look the bees knees
Quality
Value
Overall
Quality
Value
Overall
Fairly straightforward but I wish it came with documentation on what each connector does.
Quality
Value
Overall
Quality
Value
Overall
I was hoping this board would make the addition of a camera and Vtx easy and quick. Not so.

The connectors on the board are male 4 contact connections. It is very difficult to find female 4 contact connectors. I tried using 3 conductor female servo connectors without the outer sleeve. When installed there is not enough room for these connectors on the controller and battery connector and the connector will hit the top board.

The best solution is to remove all of these connectors and install header pins. Once this is done standard male servo connectors can be used. The 4th pin is for audio, which I did not use so the 3 pin connectors would work.

Somewhat disappointed as this created a lot more work than should have been necessary.

If the board would have had header pins. I would give 5 stars.
Quality
Value
Overall
Quality
Value
Overall
this is a great idea, too bad it will be useless if they ban fpv
Quality
Value
Overall
Quality
Value
Overall
So a friend and I are building dead cats. His is built and flying and after a hard landing the copper band for his ground circuit going to the defibrillator cracked and started pealing off. My frame hasn't been build because my filtered 12v to my video TX is shorted to ground out of the box. .......Not to mention his was nose heavy with a go pro 3 and a 3300mah 3 cell. So I ordered a 4000mah 3 cell because I have a heavier go pro 2 and ccd board cam for fpv but then ran into my electrical short when pinning out the board. I had high hopes for the dead cat but am having second thoughts now for sure.
Cheap lower defibrillator board.
Nose heave with a go pro sized camera. (With 3300mah)
Arms flex

Quality
Value
Overall
Quality
Value
Overall
I had bigger hopes for this. You have 5V in the front and 12V in the back and a just one extra pin intended for video between front and back. I would like to see both 5V and 12V front and back and some extra pins that I could use for whatever.



The defibrillator seems to output 10V on the 12V pin based on just a quick test with 3S.



Also note that the pins are FEMALE for everything. If they where male we could use the extra servo cables we have...



Connecting a Tarot 2D gimbal to this needs hacking. The defibrillator is in the way and the provided holes are not suitable for the Tarot. I opted to add a separate plate in between the deadcat and gimbal.
Quality
Value
Overall
Quality
Value
Overall
Totally agree, the idea is good, like the Black Sheep TBS Discovery product, but the difference is they give you hook-up pins and connectors. HK, at least give us a reference or source to find the pins we need. Come on HK, you have a good concept, follow it through and give your customers a complete product.......after all you require us to buy three different kits to get "one".
Quality
Value
Overall
Upload
Videos
  • Dead Cat PCB Board

Upload video
Upload
Files

Seuls les utilisateurs identifiés peuvent télécharger les fichiers. Merci de vous connecter ou de vous enregistrer pour commencer à aider les autres membres dès aujourd'hui!

Étiquettes des produits

Utiliser des espaces pour séparer les étiquettes. Utilisez des apostrophes pour les phrases.