Devenez fournisseur Blog Nouveaux articles
S'inscrire

Prix total

0,00 €

Panier 0 Panier 0 Loading...

Turnigy 540S V-Spec Inrunner w / Impeller 1100kv

Generating Links

Turnigy 540S V-Spec Inrunner w / Impeller 1100kv

Prix:

Now save économisez 0,00 € 0,00 €

25,88 €
Déjà acheté Discontinued Product

Please continue searching for a similar product.
SKU:
D540S-1100
Livraison gratuite? Cliquez ici pour apprendre plus!
Inrunner de couple élevé, excellente pour la course hélices sans avoir besoin d'une boîte de vitesses.
La conception de stator unique crée un bas moteur à couple élevé actuel et grand pour les remplacements de outrunner et beaucoup plus efficace que inrunners de la même taille.
Dimension: 52mm x 36mm, 66mm (avec arbre)
Poids: 141g (kv1100) (non compris les connecteurs)
Diamètre de l' arbre: 5mm
Longueur de l' arbre avant: 13mm
Epaisseur des lames: 2mm.

Spec.
Batterie: 3-4 cellulaire 4S / 14.8V
RPM: 1100kv
Courant max: 45A
Aucun courant de charge: 2.1A
Résistance interne: 75.2ohm
Données:
4S 14.8V
Prop: 8x3.8, 9x4.5, 10x5
Max: 24A, 29.4A, 35.5A
Pull: 1300g, 1570g, 1780g
ESC: 60A
  • Kv ( rpm / v) 1100.00
  • Max Current (A) 45.00
  • Résistance ( mh ) 75.00
  • Max Tension (V) 14.00
  • (W ) 0.00
  • Arbre A ( mm ) 5.00
  • Longueur B ( mm ) 51.00
  • Can Diamètre C ( mm ) 36.00
  • Longueur Can D ( mm ) 47.00
  • Longueur totale E ( mm ) 65.00
attributeset-10
Close

Dimension Diagram Guide

  • attributeset-10

Close

Télécharger une video

Inscrivez-vous pour télécharger des vidéos, s'il vous plaît se connecter ou s'inscrire

Sujets
Trier par
Sujets les plus récents
* Surnom:

* Votre réponse:


Veuillez saisir le texte affiché dans l'image dans le champ ci-dessous
*Code de vérification:
Annuler
Soumettre
Publier un nouveau sujet
* Surnom:

* Votre sujet:



Veuillez saisir le texte affiché dans l'image dans le champ ci-dessous
*Code de vérification:
Sujet du message

Inscrivez-vous pour écrire des critiques, s'il vous plaît se connecter ou s'inscrire

NZ MINNOW | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Sep 16, 2011

Update on previous review. Have tested with new HK 55A D-Lux ESC which in factory settings would not kick it off without giving prop a start by hand but once running was ok but motor still gets hot quickly even with small prop. Tried with 100A HK D-Lux ESC using Flitemax 4s 20c and this started it no probs. Using a 9x6 E prop cut down to 8'' I got 5lbs of thrust in pusher mode but motor gets too hot to touch in about 10 secs. It seems like it can take more power as it still flattens out at max rpm on 4s 20c so maybe 30c might be better.

It seems to have a major cooling issue as very little air can get past the rotor so I think it may be good in a pusher mode with direct ducting or in a boat with a copper tube wound on for water cooling. I have a 40'' Prather hull which I may try it in using this method as it certainly has the potential to be a good motor if you can cool it well.

C.C.Rid3r | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Jun 14, 2011

Nice motor, runs well, flew a Simprop Selection motorglide whit 10x5 propeller, turnigy 60A and LIPO 3S 3000 mA/h . You can see in youtoube http://www.youtube.com/watch?v=ZvrhohB9X2k&feature=player_embedded

I Recomended. But secure the external cover whit a screw.

Client | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

May 17, 2011

Tried this motor with 4s 20c 3000mah, TGY 85A ESC and with a 10x8 wooden prop and got 20A and 294W. Have tried a 9x6 three blade ic prop as well which was well within the motors specs but it (and the ESC) just get real hot on anything more than a cruise static. I have noticed it gets to full revs then backs off slightly with any prop as if it wants more power. Maybe the ESC is not suitable for this motor or the timing is wrong, (have yet to try different timing- on high timing at present).

Had pleanty of pull with the 9x6 but not sustainable as it needed better cooling. Fan is in the wrong end for planes as it draws air from the back of the motor and expells it from the front. It would be better not to have it at all and run cool air through the motor as the fan disk stops this happening.

I had to replace the bearings in the first hour or so of testing and Loctite the rear outer bearing shell to the case as it was far too loose but it now runs very smoothly and quietly and quite economically at 1/2 throttle. As tested so far - good for a light model where you need an occasional burst of good power and the rest medium throttle, Not a bad motor really but will test other ESCs / timing etc and report further

Platinium Customer | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Mar 27, 2011

J'ai command 2 moteurs Turnigy 540S. Il est IMPOSSIBLE de les faire tourner la main. Par contre avec une pince j'y arrive... J'ai pens que le couple tait vraiment trs important... Mais AUCUN de mes controleurs n'est arriv le faire tourner ! J'ai essay TOUS les rglages possibles : chaque fois, un autre moteur tourne, mais aucun des deux turnigy 540 S ne tourne ! Ils vibrent peine, c'est tout ! Trs mauvais achat pour moi...

Client | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Feb 15, 2011

Ordered 2 motors. First one is perfectly fine. Second one has the flange on the axle side loose......

Client | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Aug 22, 2010

Super Motor luft wie eine eins ohne Getriebe...!

VG Tom

Client | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Apr 21, 2010

Bought this for a Phoenix classic EP trainer (flying weight 2KG) together with a Turnigy 60 A ESC, using a 10x7 prop and 4s 4900mAh rhino lipo.Results tested showed 840w drawing 55 amps.then reduced the acceleration setting on my tx and resulted in 43 amps and 660w.Will downsize prop to 10x5 as recomended by a experienced friend. Only tricky part was fitting on motor mount/prop as shaft length a bit short, hence 5 stars a bit generous.

Kalps | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Jan 19, 2010

Can anyone help me with the connector configurations. There is no manual and I would like to know which cables are +ve,-ve and signal? Thanks.

Para un Rapid-Reichard | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Dec 30, 2009

Interesante motor lo tengo pensado para poner en un velero floton, pensado para subir facilmente y despues a planear. Lo pondre en un velero Rapid-Reichard. He pensado en este tipo de motor debido a la estrechez del morro del velero y la posibilidad de tener los cables en la parte trasera de motor para que no incordien.

| Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Oct 01, 2009

It uses it for AW28. Power goes out well, too and it is unquestionable. I think that the cooling efficiency is also good.

  1. 1
  2. 2
Fichiers clients
Measuring data Turnigy 540S V-Spec Inrun Download [87]
Téléverser un fichier

Inscrivez-vous pour télécharger des fichiers.
S'il vous plaît se connecter ou s'inscrire pour commencer à aider les amateurs maintenant!