New Items Forum
S'inscrire

Total Price

0,00 €

Panier 0 Panier 0 Loading...

Turnigy Aerodrive SK3 - 2822-1090kv Brushless Outrunner Motor

Turnigy Aerodrive SK3 - 2822-1090kv Brushless Outrunner Motor

Shipped From:
  • USA
  • Global
QTY:

Now save enregistrer 0,00 € 0,00 €

15,96 €
Statut:
En stock.
Poids
98 g
SKU:
SK3-2822-1090
WANT FREE SHIPPING? Click here to find out more!

Turnigy SK3 Motors sont le prochain bond en avant dans la qualité du moteur et du design. Nous avons demandé aux ingénieurs de la source la meilleure qualité des aimants, des roulements et des matériaux mis à leur disposition et de développer un moteur qui ne serait pas le seul rival, mais surpasser la qualité de plusieurs moteurs principaux fabricants sur le marché aujourd'hui.

Le résultat est un moteur efficace, de haut calibre en utilisant qualité doubles roulements blindés, néodyme frittés aimants et une chaîne enroulée stator en assurant un enroulement précis et cohérent à chaque fois.

Les moteurs Turnigy SK3 sont adaptés aux modélisateurs qui recherchent un moteur brushless de qualité sans compromis.

Specs.
Active: 50T
Tension: 2 ~ 3S Lipoly
RPM / V: 1090 kv
Résistance interne: 0,235 Ohm
Max Chargement: 7A
Puissance: 80W
Shaft Dia: 3.0mm
Trous de boulons: 16mm et 19mm
Fil de Bolt: M3
Poids: 31g
Branchez Moteur: 3.5mm Bullet Connector

  • UGS SK3-2822-1090
  • Brand SK3
  • Poids (g) 98.00
  • Longueur 105.00
  • Largeur 45.00
  • la taille 80.00
  • Kv ( rpm / v) 1090.00
  • Max Current (A) 7.00
  • Résistance ( mh ) 235.00
  • Max Tension (V) 11.00
  • (W ) 80.00
  • Arbre A ( mm ) 3.00
  • Longueur B ( mm ) 21.00
  • Diamètre C ( mm ) 28.00
  • Longueur Can D ( mm ) 8.00
  • Longueur totale E ( mm ) 33.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Very smooth turning. And very light weight.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Very smooth turning. And very light weight.

I love these little beasts, strong enough for a FW330, these make my 260 zoom using a 3S 2200 mAh battery. Fancy packaging, and extra mounting bits too.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I love these little beasts, strong enough for a FW330, these make my 260 zoom using a 3S 2200 mAh battery. Fancy packaging, and extra mounting bits too.

Motor macht auf dem Prfstand einen guten Eindruck. Meine Messergebnisse mit Turnigy Lipo 3/1200 und Hobbyking 12 A Regler sowie APC Style Propeller 8x4 von Hobbyking:
6,5 A, 8800 U/min, Schub: 320 g.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Motor macht auf dem Prfstand einen guten Eindruck. Meine Messergebnisse mit Turnigy Lipo 3/1200 und Hobbyking 12 A Regler sowie APC Style Propeller 8x4 von Hobbyking:
6,5 A, 8800 U/min, Schub: 320 g.

These motors where what I used for a quadcopter build a year ago and lets say they are a great choice. Flight time wise, I'm flying around 10 mins with a 0845 prop, 3s 2200 mah lipo, and 10amp escs. These motors are great for the price, they do get a little bit warm but not close to hot.
As for build quality, there is nothing to complain about except that one of the motors did get bent from a 25ft fall, as the bottom plate (the plate from where the shaft protrudes) seems to be the weakest part of the motor but then again it was 25 feet.
These motors are
Over all, I will buy these motors again as they are cheap, preform well, and look good on my quad.

Note-If you are going to get this motor, get some higher rated esc's because my 10 amp escs do get fairly hot, even at winter time.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

These motors where what I used for a quadcopter build a year ago and lets say they are a great choice. Flight time wise, I'm flying around 10 mins with a 0845 prop, 3s 2200 mah lipo, and 10amp escs. These motors are great for the price, they do get a little bit warm but not close to hot.
As for build quality, there is nothing to complain about except that one of the motors did get bent from a 25ft fall, as the bottom plate (the plate from where the shaft protrudes) seems to be the weakest part of the motor but then again it was 25 feet.
These motors are
Over all, I will buy these motors again as they are cheap, preform well, and look good on my quad.

Note-If you are going to get this motor, get some higher rated esc's because my 10 amp escs do get fairly hot, even at winter time.

Tested at 12 volts with a 8x4.5" propeller: static thrust = 369 grams, current = 6.82 A, that are good values. But the ball bearings are of a very low quality.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Tested at 12 volts with a 8x4.5" propeller: static thrust = 369 grams, current = 6.82 A, that are good values. But the ball bearings are of a very low quality.

Good motor for small planes, It runs on 2 or 3 cell lipo and 8x4.5 prop with a 12 amp esc on my Magnum Reloaded.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Good motor for small planes, It runs on 2 or 3 cell lipo and 8x4.5 prop with a 12 amp esc on my Magnum Reloaded.

These are very good motors, especially for a medium-sized quadcopter (I use the SK450 frame with these). not too expensive, yet good quality. Lots of bang for your buck.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

These are very good motors, especially for a medium-sized quadcopter (I use the SK450 frame with these). not too expensive, yet good quality. Lots of bang for your buck.

Bought 2 pcs, but only bench tested them so far: 7.4Amps at 10.4Volt (semi charged 3S LiPo) with 8x4.5" prop. Quality seems fine.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Bought 2 pcs, but only bench tested them so far: 7.4Amps at 10.4Volt (semi charged 3S LiPo) with 8x4.5" prop. Quality seems fine.

vraiment tip top ses moteurs,

un ptit bemol, les 3 phases ne sortent pas toujours du mme ct par rapport au fixation du moteur. Ou ptte la faute pas d'chance

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

vraiment tip top ses moteurs,

un ptit bemol, les 3 phases ne sortent pas toujours du mme ct par rapport au fixation du moteur. Ou ptte la faute pas d'chance

Very nice little motor.
It is a comparable motor to the KDA 20-50S.

33g with 2mm gold connectors and the prop holder (fixed with 3 screws).
The 3 screws are not the best quality, so don't screw them too strong, or the winding will break.

I have measured this motor (and the KDA 20-50S) with my Eagletree gear and uploaded the data to drivecalc. You can use this program to try different props. and find the right configuration.
(Turnigy SK3 2822-1090 - timing high)

perfect motor for small quadcopters:
measured for example following combination:
Turnigy Plush 10A
Maxx Pro. EPP0845 Prop.
Voltage: 11,15V
Current: 8,30A
RPM: 7132
thrust: around 425g

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Very nice little motor.
It is a comparable motor to the KDA 20-50S.

33g with 2mm gold connectors and the prop holder (fixed with 3 screws).
The 3 screws are not the best quality, so don't screw them too strong, or the winding will break.

I have measured this motor (and the KDA 20-50S) with my Eagletree gear and uploaded the data to drivecalc. You can use this program to try different props. and find the right configuration.
(Turnigy SK3 2822-1090 - timing high)

perfect motor for small quadcopters:
measured for example following combination:
Turnigy Plush 10A
Maxx Pro. EPP0845 Prop.
Voltage: 11,15V
Current: 8,30A
RPM: 7132
thrust: around 425g

  1. 1
  2. 2
Customer files
Drawing Download [86]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save