New Items Actus Forum
S'inscrire

Total Price

0,00 €

Panier 0 Panier 0 Loading...

Turnigy Power Unit double pour modèles à grande échelle

Turnigy Power Unit double pour modèles à grande échelle

Shipped From:
  • Global

Now save enregistrer 0,00 € 0,00 €

21,52 €
Alert me
Statut:
Epuisé!
SKU:
TR-PWU
ETA:
No ETA At This Time [ ? ]
WANT FREE SHIPPING? Click here to find out more!
Power Unit Turnigy pour les modèles à grande échelle.
Dans les grands avions à grande échelle la sécurité est primordiale. Cest pourquoi vous avez besoin d'un système de forte puissance avec deux régulateurs pour assurer un contrôle continu.
Caractéristiques;
Fonctionne avec toute radio
Plus de puissance pour tous les servos
régulateur de tension linéaire double avec sortie courant élevé
6.2V / 6.7V sélectionnable, 8A puissance directe pour servos Haute-drain
5.3V, puissance 5A d'alimentation du récepteur / Gyro / petits servos
Robuste d'entrée 16AWG.
Compatible avec servo standard bouchons JR / Futaba.
Accepte 7.4V à 12.6V batterie tension d'entrée.
Poids: 89g


  • UGS TR-PWU
  • Brand Turnigy
  • Capacité ( mAh ) -
  • Poids 127.0000
  • Longueur 140.00
  • Packaging Width 15.00
  • la taille 115.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Perfect alternative for other top brand power unit that can break your wallet.
I use 2 of these for my 50cc pilot-rc sbach.
At that moment I only had 5 of 35kg servos in hand, I know it is an overkill, but I can't wait to get another smaller torque servo.
This 35kg servo can draw almost 3 Amperes.
You can use 2 of these on 1 transmitter, how?

Decide which unit you will use to supply the RX unit, lets say this is A unit.
And B unit is the other one.
I use 2 aileron and throttle on A unit, rudder and elevator on unit A,
MAKE SURE you CUT the POSITIVE( /middle/red) wire on the jumper cable from TX to the power unit.
I use RX power channel on unit B to power my ignition and it works fine, I have no problem with my T8FG FASST Futaba radio system.
The disctance between ignition system to the power unit is less than 4" or 10cm. I didn't have any servo glitch.
So far I am very happy with it, I can get 10 of this compare 1 to the other brand and yet the same result.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Perfect alternative for other top brand power unit that can break your wallet.
I use 2 of these for my 50cc pilot-rc sbach.
At that moment I only had 5 of 35kg servos in hand, I know it is an overkill, but I can't wait to get another smaller torque servo.
This 35kg servo can draw almost 3 Amperes.
You can use 2 of these on 1 transmitter, how?

Decide which unit you will use to supply the RX unit, lets say this is A unit.
And B unit is the other one.
I use 2 aileron and throttle on A unit, rudder and elevator on unit A,
MAKE SURE you CUT the POSITIVE( /middle/red) wire on the jumper cable from TX to the power unit.
I use RX power channel on unit B to power my ignition and it works fine, I have no problem with my T8FG FASST Futaba radio system.
The disctance between ignition system to the power unit is less than 4" or 10cm. I didn't have any servo glitch.
So far I am very happy with it, I can get 10 of this compare 1 to the other brand and yet the same result.

Works and gives the required power.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Works and gives the required power.

There is a bit of speculation and mis-information about this product here. Let's see if I can clear a few things up.



First:



This is NOT a "four channels" only product.



Rather it provides 8 amps of power to four sets of pin-outs. You can use this device as you wish for MORE than four channels... read on.



Second:



The "input" side also provides 5 amps of power to your connected device.



So if you plug your receiver's aileron output to one of the power unit's input channels, your receiver and everything connected to it, get 5A of power.



Third:



Treat the "input" pins as power sources.



Fourth:



It works fine and maybe best with 3S LiPo packs. Regulators have better "reserves" when the supply voltage is on the higher side of their specified range.



Fifth:



6.2 - 6.7 volts is perfect for 6v servos.



Remember that these devices are designed to work with 6v battery packs. On a fully charged 6v battery the voltage will go as high as 8.2v initially. It drops off once a load is put on the battery.



6.2 - 6.7 is well within specs for 6v devices.



-



I wanted to power a 50cc biplane and used this unit with great success. I hooked up one aileron channel of the RX to channel 1 input on the power unit. I hooked up the other aileron channel ( so I can get differential ) to channel 2 input on the power unit. I hooked up the ailerons via two"Y" cables to p

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

There is a bit of speculation and mis-information about this product here. Let's see if I can clear a few things up.



First:



This is NOT a "four channels" only product.



Rather it provides 8 amps of power to four sets of pin-outs. You can use this device as you wish for MORE than four channels... read on.



Second:



The "input" side also provides 5 amps of power to your connected device.



So if you plug your receiver's aileron output to one of the power unit's input channels, your receiver and everything connected to it, get 5A of power.



Third:



Treat the "input" pins as power sources.



Fourth:



It works fine and maybe best with 3S LiPo packs. Regulators have better "reserves" when the supply voltage is on the higher side of their specified range.



Fifth:



6.2 - 6.7 volts is perfect for 6v servos.



Remember that these devices are designed to work with 6v battery packs. On a fully charged 6v battery the voltage will go as high as 8.2v initially. It drops off once a load is put on the battery.



6.2 - 6.7 is well within specs for 6v devices.



-



I wanted to power a 50cc biplane and used this unit with great success. I hooked up one aileron channel of the RX to channel 1 input on the power unit. I hooked up the other aileron channel ( so I can get differential ) to channel 2 input on the power unit. I hooked up the ailerons via two"Y" cables to p

Exellente producto lo coloque en un sbach 342 de goldwing y funciona de maravilla!
Ademas muy buen precio y exellente prestaciones.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Exellente producto lo coloque en un sbach 342 de goldwing y funciona de maravilla!
Ademas muy buen precio y exellente prestaciones.

Super regulateur surtout pour moi je l'instala dans hk 500 avec tout un materiel a bort telemetrie et plusplusplus

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Super regulateur surtout pour moi je l'instala dans hk 500 avec tout un materiel a bort telemetrie et plusplusplus

affidabile centralina a costo invidiabile

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

affidabile centralina a costo invidiabile

j'en ai achet un pour le tester, et aprs avoir branch 4 servo digitaux chargs chacun avec 2 3 kg de poids 2 cms.
le courant d'appel oscillait entre 4 et 5 ampres. pendant plusieurs minutes, il chauffe un peu, c'est normal, mais pas de problme, il supporte au moins 4 ampres sans se couper ou bruler !
peut tre ai je eu de la chance et suis je tomb sur un exemplaire plus fiable qu'un autre ???

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

j'en ai achet un pour le tester, et aprs avoir branch 4 servo digitaux chargs chacun avec 2 3 kg de poids 2 cms.
le courant d'appel oscillait entre 4 et 5 ampres. pendant plusieurs minutes, il chauffe un peu, c'est normal, mais pas de problme, il supporte au moins 4 ampres sans se couper ou bruler !
peut tre ai je eu de la chance et suis je tomb sur un exemplaire plus fiable qu'un autre ???

Type your review here.
Try to include as much data as possible.
I use this little and inexpensive gadget to secure the current on my receivers, they handle the current to your servos very well, I four 2200 mAh (two packs of 2 in parallel) Li Ion batteries and they work perfectly, the only thing I would recommend Turnigy is to verify that each one of the modules includes the bridge joiner for the voltage selection (6.2 or 6.7) as the last 4 that I have ordered have been missing. Other than that I love these units they work great and gives me a sense of confidence with my large planes.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Type your review here.
Try to include as much data as possible.
I use this little and inexpensive gadget to secure the current on my receivers, they handle the current to your servos very well, I four 2200 mAh (two packs of 2 in parallel) Li Ion batteries and they work perfectly, the only thing I would recommend Turnigy is to verify that each one of the modules includes the bridge joiner for the voltage selection (6.2 or 6.7) as the last 4 that I have ordered have been missing. Other than that I love these units they work great and gives me a sense of confidence with my large planes.

perfecto para aviones gran escala

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

perfecto para aviones gran escala

My Giant quarter scale electric Spitfire flies using one of these. Never a moments worry. Has 2 flap, 2aileron.2elevator &1 rudder servos. These are rated at 7 VOLTS, so 6.7 is spot on. The reciever & retract servo are on the 5.3V feed. I make my own extension & Y-leads. I do not use any switches in the radio equipment. I simply plug in a 2-cell lipo, test the radio systems, then I fit the Motor batteries + battery telemetry (Quanum) and go fly.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

My Giant quarter scale electric Spitfire flies using one of these. Never a moments worry. Has 2 flap, 2aileron.2elevator &1 rudder servos. These are rated at 7 VOLTS, so 6.7 is spot on. The reciever & retract servo are on the 5.3V feed. I make my own extension & Y-leads. I do not use any switches in the radio equipment. I simply plug in a 2-cell lipo, test the radio systems, then I fit the Motor batteries + battery telemetry (Quanum) and go fly.

  1. 1
  2. 2
  3. 3
  4. 4
Customer files
multimodul2.hex Download [8]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Radio Control Planes, Drones, Cars, FPV, Quadcopters and more - Hobbyking