Servo Turnigy FBL100 linéaire

• Overall
• Quality
• Value

Customer Rated

Feb 15, 2014

It is like the other reviews tell you for using it on a MCPX, i left the red cable as it was and changed the other two with soldering in the middle. Some one change it at the plug itselve, but i couldnt manage this. I have some flight with my mcpx and there it works fine!

Panzi

• Overall
• Quality
• Value

Certified Buyer Rated

Nov 12, 2013

better value than the MCPX replacement servos. Functions just as well. Just have to be careful with the wires going from the servo to the gyro. They are very brittle. I recommend putting a spot of glue where the wires are soldered to the servo board for extra reinforcement. This is how the Blade MCPX servos are made.

• Overall
• Quality
• Value

Customer Rated

Sep 17, 2013

My original FBL100 lasted a long time with many many crashes before two servos needed replacing. I ordered two replacements and one had a complete short that fried the wires running to the servo and damaged the main helicopter board beyond repair. Now I'm forced to replace all the electronics or just get a new helicopter...
Not pleased. Come on HK, test your products before shipping them to the customer!

• Overall
• Quality
• Value

Certified Buyer Rated

Sep 17, 2013

bought for my wltoys v922.

• Overall
• Quality
• Value

Certified Buyer Rated

May 25, 2013

excelente produto, pode confiar, otimo preco... no Brasil nao tem igual. faz tudo o que esta proposto a fazer com uma qualidade muito boa, pois pelo preo que se paga achei que seria um produto de baixa qualidade, mais nao, de tamanha qualidade e competncia. valeu Hobbyking

• Overall
• Quality
• Value

Certified Buyer Rated

Feb 17, 2013

Price / quality ratio is very good I recommend Daniel!!!

• Overall
• Quality
• Value

Customer Rated

Dec 14, 2012

I had to resolder ALL THREE connection wires to the board but that didnt matter as I had to interchange the black and white wire anyway for use on the mCPX.
You also have to drill the two holes for the screws and the one to fit on the tiny bolt to 1.5 mm in order to have them fit on the mCPX. Upon doing this its a perfect, cheaper, and even better looking ;-) servo for the mCPX. Best thing of all I can use them on my FBL 100 as well ;-).
All in all, highly recommended servo. And, all in all, I do recommend the FBL100.

• Overall
• Quality
• Value

Certified Buyer Rated

Dec 12, 2012

Otimo produto! Recomendo a compra!!

• Overall
• Quality
• Value

Customer Rated

Nov 28, 2012

Answer: (cant answer to question directly, donno, why):
Hi,
easy to do - take a mCP x servo and put wires according to those.
Eflite red = FBL100 red; Eflite brown = FBL100 black, Eflite orange = FBL 100 white.
No soldering or crimping necessary; take a needle (or tiny screwdriver or...) and push on the metal part/lift the plastic part of the plug cap, pull the white and black plug out and press it in again on the other colours former position.
You do not have to change the red wire plug, only change black (Eflite brown) and white (Eflite orange).

• Overall
• Quality
• Value

Certified Buyer Rated

Nov 02, 2012

If you change plug polarity (easy to do), this servo will work on mCP x and Nano CPx boards.

Board of servo is little bigger than Eflite boards - so you cant use it as nick-servo. You have to cut a little bit of the servo board to mount it as front servo on mCP x, no cutting necessary on Nano board. Cannot say anything so far about durability, received the servo recently. Anyway, not really cheap, quite expensive for Hobbyking servos, ...