New Items Forum
S'inscrire

Total Price

0,00 €

Panier 0 Panier 0 Loading...

Turnigy Multistar 10 Amp multi-rotor Brushless 2-3S

Turnigy Multistar 10 Amp multi-rotor Brushless 2-3S

Discontinued Product

Please continue searching for a similar product.
Poids
20 g
SKU:
9351000001
WANT FREE SHIPPING? Click here to find out more!

MultiStar CES sont sont un régulateur de vitesse de qualité à un prix fantastique! Conçu pour une installation simple et une configuration facile ces CES ont prouvé pour offrir une excellente performance lorsqu'il est utilisé dans des applications multi-rotor. Si votre départ en Multi-rotors et ont besoin d'une solution facile à installer qui est testée et éprouvée à travailler avec Multi-aérogire alors ces contrôleurs de vitesse sont faites pour vous.

Ces ESC de dispose d'une réponse à l'accélérateur linéaire encore très lisse, sans pour autant sacrifier un rapide, vif, la réponse à une entrée de gaz. La sécurité est pas oubliée avec avec la batterie de tous les Multistar Esc réglable LVC (set type de batterie à LiXX pour désactiver LVC), moteur en panne (surcharge) la protection, la perte de signal arrêt et d'armement en toute sécurité.

Toutes les séries Multistar ESC est venu avec des connecteurs de balles installés qui sont adaptés à la gestion de la puissance nominale de l'ESC. Cela permet de plug and play pratique en ajoutant simplement le diviseur approprié d'alimentation de la batterie (3,4 ou 6 ESC) et extensions moteur de plomb à partir de la ligne d'accessoires modulaire Multistar. Quoi de plus simple?

La fonction de tous Multistar ESC une MCU ATmega qui ouvre la porte à firmware personnalisable - pour ceux que cela intéresse! ou encore une carte de programmation peut être utilisé avec le logiciel installé pour une installation rapide et facile avec le logiciel pré-flashé.

S'il vous plaît se référer aux articles connexes ci-dessous pour une solution d'alimentation multi-rotor sans soudure en fonction de votre projet multi-rotor suivant.

Caractéristiques:
• Contrôle lisse et linéaire papillon
• Réponse rapide à l'entrée des gaz
• Atmel MCU
• Protection du moteur Stalled
• Le signal d'accélérateur perdre la protection
• la mise sous tension (gaz lockout) Coffre-fort
• Prise en charge 480Hz + taux de rafraîchissement élevés (jusqu'à 499hz)
• Compatible avec la carte de programmation

Spécifications:
Constant: 10A
Tension d'entrée: 2-3 cellules Lipoly
BEC: Oui (linéaire) [Retirez le fil du milieu pour dissable]
BEC Sortie: 5V / 2A
MID: 8 KHz
RPM Max: 240,000rpm pour 2 Pole moteur Brushless
PCB Taille: 22mm x 17mm
Décharge Plugs: Connecteur mâle Bullet 2mm
Moteur Plugs: 2mm Femme Bullet Connector
Poids: 16g

Mode d' emploi maintenant disponible pour téléchargement sous l' onglet "Fichiers".

  • UGS 9351000001
  • Brand -
  • Capacité ( mAh ) -
  • Poids (g) 20.00
  • Longueur 110.00
  • Largeur 10.00
  • la taille 100.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

So tiny and lightweight and perfect! Already ready to go with 2mm connectors on all the wires. At this price its a no brainer.. Perfect for my 250!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

So tiny and lightweight and perfect! Already ready to go with 2mm connectors on all the wires. At this price its a no brainer.. Perfect for my 250!

Don't bother with these they don't perform well at all. and can not be flashed with socket tool as atmega chip is to small very small. wast of money get some Simon k instead I'm very disappointed with these want my money back their useless for multi rotors!!!!!!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Don't bother with these they don't perform well at all. and can not be flashed with socket tool as atmega chip is to small very small. wast of money get some Simon k instead I'm very disappointed with these want my money back their useless for multi rotors!!!!!!

Mis avec turnigy multistar 1704 pas de surchauffe bon vario

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Mis avec turnigy multistar 1704 pas de surchauffe bon vario

Bought these for my 250 mini quad with multistar 1704 motors and mini APM flight controller. I did also got the program card and set them up best i can. Even on NIxx on lowest setting my battery alarm goes off and they are already cutting the power to the motors. I am gonna try the HK f10a flashed with simonk next as these will eventually lead to a bad crash. Also the overload cut off is annoying because if you touch back down one or more motors will quit and you have to disarm and rearm. I am not sure why they engineered these the way they did since basically they are not good for multirotors at all??

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Bought these for my 250 mini quad with multistar 1704 motors and mini APM flight controller. I did also got the program card and set them up best i can. Even on NIxx on lowest setting my battery alarm goes off and they are already cutting the power to the motors. I am gonna try the HK f10a flashed with simonk next as these will eventually lead to a bad crash. Also the overload cut off is annoying because if you touch back down one or more motors will quit and you have to disarm and rearm. I am not sure why they engineered these the way they did since basically they are not good for multirotors at all??

Good esc(s) placed in my 330 frame with a KK2.1 board flashed with 1.11 firmware, 3s 1000mah Zippy compact batt, Turnigy 10amp Multistar esc(s) 8ch 9x receiver, power board soldered the esc direct to it and XT60 batt plug on it, 8045 props, this thing it a rocket and getting 6 minutes flight time. After flight everything is cool. Will hoover with only 40pcnt throttle. Motors are Turnigy D2822/17 1100 kv. I did soldered 3.5 bullet ends on everything.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Good esc(s) placed in my 330 frame with a KK2.1 board flashed with 1.11 firmware, 3s 1000mah Zippy compact batt, Turnigy 10amp Multistar esc(s) 8ch 9x receiver, power board soldered the esc direct to it and XT60 batt plug on it, 8045 props, this thing it a rocket and getting 6 minutes flight time. After flight everything is cool. Will hoover with only 40pcnt throttle. Motors are Turnigy D2822/17 1100 kv. I did soldered 3.5 bullet ends on everything.

No better than any non flashed esc for multirotors, after flashing with simonk they are 10x better, but this is not easy as there are no pads and the hk flashing tool is too big for the atmega chip on this esc, so you have to solder directly to the chips pin outs. For this reason I would not buy anymore as there are others available that are far easier to flash. If they are specifically for multirotors why does it have brake settings, set to medium as default lol.

They also have no throttle calibration, they are auto like dji escs, but you get throttle calibration when flashed.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

No better than any non flashed esc for multirotors, after flashing with simonk they are 10x better, but this is not easy as there are no pads and the hk flashing tool is too big for the atmega chip on this esc, so you have to solder directly to the chips pin outs. For this reason I would not buy anymore as there are others available that are far easier to flash. If they are specifically for multirotors why does it have brake settings, set to medium as default lol.

They also have no throttle calibration, they are auto like dji escs, but you get throttle calibration when flashed.

i've got a few brands of 10amps this is the one which fits me the best especially compared to the piece of crap red brick also from here...

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

i've got a few brands of 10amps this is the one which fits me the best especially compared to the piece of crap red brick also from here...

Really cool ESC for mini quadcopter. I use them with Turnigy Multistar 1704-1900K, kk2.1. And works well. I calibrated them straight kk board.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Really cool ESC for mini quadcopter. I use them with Turnigy Multistar 1704-1900K, kk2.1. And works well. I calibrated them straight kk board.

nice little ESC. Runs without flashing to SimonK also good enough for smaller Multicopter.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

nice little ESC. Runs without flashing to SimonK also good enough for smaller Multicopter.

Works ok, but gets hot faster than eg. the tgy plush esc. Bought a bunch for a small quad and put another on a bonsai flying wing. Dont forget to get the programming card too!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Works ok, but gets hot faster than eg. the tgy plush esc. Bought a bunch for a small quad and put another on a bonsai flying wing. Dont forget to get the programming card too!

  1. 1
  2. 2
  3. 3
Customer files
Manual - Turnigy Multistar Brushless ESC Download [2384]
Multistar 10A SimonK 1 Download [115]
No File Name Download [94]
Turnigy Multistar ESC Manual Download [2384]
No File Name Download [214]
Multistar 10A flashed with simonk 1 Download [819]
Multistar 10A flashed with simonk 3 Download [3348]
Multistar10A-1 Download [229]
Multistar10A-2 Download [167]
Turnigy ESC All Download [2298]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save