Turnigy Multistar 10A V2 ESC Avec BLHeli et 2A LBEC 2-3S V

• Overall
• Quality
• Value

yak 55 foamie

Sep 13, 2017

Im running this on a yak 55 32" 3d foamie i built. This one is heavy at 350g with a 850mah 3s batterie due to the foamboard used (it should be 170g with a 2s 300mah batterie if the correct foam is used)
im using the motor and prop that was recomended in the build, at 3s it flies fine even hovers. ESC seems to be coping fine

• Overall
• Quality
• Value

Perfect Motor for QAV1306-3100kv

Dec 17, 2016

I use one of these on a 48cm flying wing of around 110 gram with the QAV1306-3100kv and a 2s nano-tech 1000mAh (+50g = around 160g). 5045 Prop is fine on 2s, for 3s a 4050 was almost to much.

• Overall
• Quality
• Value

Certified Buyer Rated

Apr 12, 2016

A fine ESC. Doesn't get too hot and provides me enough power.

• Overall
• Quality
• Value

Customer Rated

Jan 24, 2016

Very light, very small, but its not 10A.
Gets pretty hot even under 5-7 amps in hover mode while cooled by props air flow.
I used them in my Trifecta, they power 1806 motors.

• Overall
• Quality
• Value

Certified Buyer Rated

Jun 03, 2015

Love these esc. I kept going back to my loved afro esc but for the spidex a throw away quad this inexpensive but we'll performing esc is doing the trick.

• Overall
• Quality
• Value

Customer Rated

Feb 21, 2015

Great ESC for the price. the V2s are a MUST have for a budget multirotor.

I've paired these with the DYS BE1806s and they work quite well once programmed. However, it is important to note that when using the USB programmer you must remove the power lead from the USB programmer to this specific ESC as these ESCs have their own power UBEC.

Additionally, it should be noted that when upgrading the UBEC firmware, you must disable demagnetic compensation completely to ensure you don't burn up your high KV motors. (This features is only available for v13 of the firmware for these ESCS)

So far these have provided cool, steady power to my DYS BE1806s, and calibration was as easy as pie.

My only problem is one of these ESCs (of 6) came faulty and fried the windings on two of my motors. However HK was quick to replace them without issue.

• Overall
• Quality
• Value

Certified Buyer Rated

Feb 04, 2015

Pretty good ESC's. I noticed people are burning these things out a lot. You can't use a high KV motor. Max I would run is the 1900KV on a 250 quad. A 2150kv baby beast would surely burn it out. It works well if you're only planning to use it for a light weight low powered quad with a 5" prop. A 6" prop would blow this ESC. Know the limits and you'll be happy. They are oddly shaped which makes me a bit awkward to mount, aside from that, no complaints. Great price for a decent entry level ESC. Needs calibration out of the box.

• Overall
• Quality
• Value

Certified Buyer Rated

Jan 14, 2015

Small, silicon cable, work great with my motors.

• Overall
• Quality
• Value

Certified Buyer Rated

Dec 29, 2014

No problems running these ESC with DYS 1806 2300kv motors. It's just a shame that the on-board capacitor makes these ESC a little thinker than usual. If you are looking to re-solder the wires onto the ESC, you need to be quite careful, the solder pads for the motors wires are not on the edge of the board, but in the middle (HW Skywalker style!)

• Overall
• Quality
• Value

Customer Rated

Nov 25, 2014

The Bad:
1) One of 4 came dead. It was replaced by warranty, but god knows when it will arrive.
2) Cucumbercome hardware assembly.

The Good:
1) Works.
2) Starting with BLHeli (and BLHeliSuite) 12.2 this ESC is officially supported.

The Bottom:
One of working 3 was with different settings. So it has sense to check settings before use. Also keep in mind that you can only program it with BLHeliSuite or in programming mode with remote(not very handy). Also I was foolish to order only 4. You probably will need spare one anyway.