Devenez fournisseur Blog Nouveaux articles
S'inscrire

Prix total

0,00 €

Panier 0 Panier 0 Loading...

Turnigy Multistar 30 Amp Multi-rotor Brushless 2-4S (OPTO)

Generating Links

Turnigy Multistar 30 Amp Multi-rotor Brushless 2-4S (OPTO)

Prix:

Now save économisez 0,00 € 0,00 €

14,18 €
Déjà acheté Discontinued Product

Please continue searching for a similar product.
SKU:
9351000008
Livraison gratuite? Cliquez ici pour apprendre plus!

MultiStar CES sont sont un régulateur de vitesse de qualité à un prix fantastique! Conçu pour une installation simple et une configuration facile ces CES ont prouvé pour offrir une excellente performance lorsqu'il est utilisé dans des applications multi-rotor. Si votre départ en Multi-rotors et ont besoin d'une solution facile à installer qui est testée et éprouvée à travailler avec Multi-aérogire alors ces contrôleurs de vitesse sont faites pour vous.

Ces ESC de dispose d'une réponse à l'accélérateur linéaire encore très lisse, sans pour autant sacrifier un rapide, vif, la réponse à une entrée de gaz. La sécurité est pas oubliée avec avec la batterie de tous les Multistar Esc réglable LVC (set type de batterie à LiXX pour désactiver LVC), moteur en panne (surcharge) la protection, la perte de signal arrêt et d'armement en toute sécurité.

Toutes les séries Multistar ESC est venu avec des connecteurs de balles installés qui sont adaptés à la gestion de la puissance nominale de l'ESC. Cela permet de plug and play pratique en ajoutant simplement le diviseur approprié d'alimentation de la batterie (3,4 ou 6 ESC) et extensions moteur de plomb à partir de la ligne d'accessoires modulaire Multistar. Quoi de plus simple?

La fonction de tous Multistar ESC une MCU ATmega qui ouvre la porte à firmware personnalisable - pour ceux que cela intéresse! ou encore une carte de programmation peut être utilisé avec le logiciel installé pour une installation rapide et facile avec le logiciel pré-flashé.

S'il vous plaît se référer aux articles connexes ci-dessous pour une solution d'alimentation multi-rotor sans soudure en fonction de votre projet multi-rotor suivant.

Détails:
• Contrôle lisse et linéaire papillon
• Réponse rapide à l'entrée des gaz
• Atmel MCU
• Protection du moteur Stalled
• Le signal d'accélérateur perdre la protection
• la mise sous tension (gaz lockout) Coffre-fort
• Prise en charge 480Hz + taux de rafraîchissement élevés (jusqu'à 499hz)
• Compatible avec la carte de programmation

Spécifications:
Constant: 30A
Tension d'entrée: 2-4 cellules Lipoly
BEC: Aucun (OPTO)
MID: 8 KHz
RPM Max: 240,000rpm pour 2 Polonais moteur Brushless
PCB Taille: 41mm x 24mm
Prises de décharge: Male 3.5mm Bullet Connector
Motor Plugs: Femme 3.5mm Bullet Connector
Poids: 32g

Télécharger une video

Inscrivez-vous pour télécharger des vidéos, s'il vous plaît se connecter ou s'inscrire

Sujets
Trier par
Sujets les plus récents
* Surnom:

* Votre réponse:


Veuillez saisir le texte affiché dans l'image dans le champ ci-dessous
*Code de vérification:
Annuler
Soumettre
Publier un nouveau sujet
* Surnom:

* Votre sujet:



Veuillez saisir le texte affiché dans l'image dans le champ ci-dessous
*Code de vérification:
Sujet du message

Inscrivez-vous pour écrire des critiques, s'il vous plaît se connecter ou s'inscrire

Sndel | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Jan 08, 2015

ESCs are OK!
They heat-up a bit at 15Amps, a bit jumpy at start but ok in overall. You just can't beat the price.
Their cooling can be improved greatly if the wrapping is taken off (carefully, don't short-out anything on them!) and the heat spreader is exposed directly to airflow or propwash.

Even better, stick them spreader-side on the booms if they are square aluminum type. (zip ties, some thermal grease, you know.. ) Everybody put's their ESCs with the heat spreader facing outwards even if they have metallic booms that could take the heat away fast.

Christian | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Aug 31, 2014

I use them in a 2.1Kg Quad. They work but 30A is quite overstated. You guys should write realistic numbers on your stuff.

Hovering current per ESC is 5-7A (Measured with accurate industrial clamp meter) and flying current up to 17A so they should handle is with ease but two of them get really hot.
No matter to which motor I hook them up, it's always the same two that get hot...

I really can't imagine this ESC to work at currents above 20A.

Ordered TurnigyPlush now.

Stephen | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Aug 19, 2014

A great ESC, i have these on 2 of my multi-rotors and am very happy with them, they do not get too hot and are very smooth

SamdeJ | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Aug 05, 2014

These ESCs are rated for 30Amps.... but it cannot handle more than 6 Amps.. all four of them over heads and shuts down randomly in 4 to 5 minutes of flying.. my quad crashed 3 times due this problem and third time into pieces... these escs are crap.. never again buy these ones....

mohag | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Aug 01, 2014

Decent ESC... You likely want the programming cards as well though, since you can't configure much without it.

If you want ESCs for a multirotor, you are likely better off with AfroESC than with these. They might make a nice low cost option if you are willing to flash them yourself though... (The 40A ones have an all-NFET design, which should have better performance though)

I haven't flashed mine yet, stock firmware is OK...

Erkin | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Jun 03, 2014

no need simonK firmware i think. it's very good with stock firmware but it needs little bit programming. on some frames (X650F) it doesn't fit esc mount and cables are too short

chly3001 | Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Feb 21, 2014

bought multistar esc for use with multirotor obviously. wondering if the f-20a/f-30a might be a better choice for the FETs, but currently these are pretty good. going to flash them with simonk.

Thomas | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Dec 18, 2013

Good ESC but not great, I tried them in a quad that I have SimonK controllers with a KK2 board and it took a lot of adjusting but didn't fly as well, but was better than a regular ESC.

These OPTO units don't seem to like being flashed with SimonK firmware, I flashed mine with the KDA file and smoke started coming out of my test motor, though I've seen people succeed with the BEC version, I may have had a dud but wasn't willing to try anymore.

| Acheteur vérifié

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Nov 30, 2013

i guess it is ok to use it as it is, but don't try to flash it with simonk firmware because they won't work smoothly. jerky movements and not reliable when flashed.

Schnufftuff | Acheteur vérifié

  • Overall
  • Quality
  • Value

Customer Rated

Nov 21, 2013

alle 4 gelieferten Regler nicht in Ordnung gewesen! Gleiche bei einem Kollegen. Hoffe das war nur eine schlechte Serie und es wird behoben.

  1. 1
  2. 2
  3. 3
Fichiers clients
Turnigy Multistar ESC User Manual Download [2384]
ESC-bad Download [165]
opto board2 Download [346]
board_a Download [244]
board_b Download [235]
Téléverser un fichier

Inscrivez-vous pour télécharger des fichiers.
S'il vous plaît se connecter ou s'inscrire pour commencer à aider les amateurs maintenant!