Diventa fornitore Blog Nuovi oggetti
Registrati

Prezzo totale

0,00 €

Carrello della spesa 0 Carrello della spesa 0 Loading...

2725 1600kv Brushless Outrunner Motor

Generating Links

2725 1600kv Brushless Outrunner Motor

Prezzo:

Now save risparmia 0,00 € 0,00 €

11,14 €
Già acquistato Discontinued Product

Please continue searching for a similar product.
SKU:
074000063
Spedizione gratuita? Clicca qui per saperne di più!

2725 1600kv Brushless Outrunner Motor

Specifiche:
Dimensioni: 27mm x 25mm
Peso: 35g
KV: 1600 rpm / v
Voltaggio: 7.4V ~ 11.1V (2s ~ 3s)
Max corrente: 17A
Potenza massima: 190W
Albero: 3mm

* Il colore può variare

  • Kv ( rpm / v ) 1600.00
  • Correnti Max (A) 17.00
  • Resistenza ( mh ) 0.00
  • Max Tensione (V ) 11.00
  • Potenza ( W ) 190.00
  • Albero A ( mm ) 3.00
  • Lunghezza B ( mm ) 20.00
  • Diametro C ( mm ) 27.00
  • Can Lunghezza D ( mm ) 10.00
  • Lunghezza totale E ( mm ) 45.00
attributeset-10
Close

Dimension Diagram Guide

  • attributeset-10

Close

Carica video

Registrati per caricare video, per favore accedi o registrati

Temi
Ordina per
Argomenti più recenti
* Nickname:

* La tua risposta:


Si prega di inserire il testo mostrato nell'immagine nel campo sottostante
*Codice di verifica:
Annulla
Invia
Pubblica un nuovo argomento
* Nickname:

* Il tuo argomento:



Si prega di inserire il testo mostrato nell'immagine nel campo sottostante
*Codice di verifica:
Pubblica argomento

Registrati per scrivere recensioni, per favore accedi o registrati

richard | Acquirente verificato

  • Overall
  • Quality
  • Value

Customer Rated

Jan 21, 2015

Worked fine at first. Didn't take long to figure out there is a quality control issue with this motor. At about 3/4 throttle it came to a screeching halt. Drop throttle and start again with same results. Found out that the stator with the wire windings worked loose from the motor housing. At about 3/4 throttle it would start to spin on the housing and lose timing causing it to stop. All three of these motors i got do the same thing. So it wasnt just a fluke. I assume that separating the motor and glueing the stator on firmly will fix the issue. I am waiting for one to dry to test it.

| Acquirente verificato

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Oct 09, 2014

good engine

put it on biks3

now learning to fly)

Evil Pusher | Acquirente verificato

  • Overall
  • Quality
  • Value

Customer Rated

Oct 04, 2014

whatever Ive writen before - forget it - this motor is rubbish. Bearing becoming hot on 3S, one of two was burning by using an 8x6 prop. POS

Evil Pusher | Acquirente verificato

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Sep 15, 2014

nice little outrunner - bearings seems to be okay. easy to install - like shaft on both side.

__Raju | Acquirente verificato

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Jul 03, 2014

It is good motor but where is motor mount? draw more current, gives less thrust compared to other motors in it's size. It is not bad motor but also not very good one, something in between.

| Acquirente verificato

  • Overall
  • Quality
  • Value

Certified Buyer Rated

May 22, 2014

Great little motor. Attached this my my makeshift hovercraft and worked a treat, plus the fact that it didn't cost a lot was a bonus.

Geoffro | Acquirente verificato

  • Overall
  • Quality
  • Value

Customer Rated

May 09, 2014

Badly designed motor. They have decent grunt but the shaft is stupidly long at the rear and cannot be adjusted. You would think you can take the grub screws out and the housing the slide the shaft up? no.. took them apart... the stop of the shaft is fixed to the spinner, it's not sliding anywhere. They also have a chunky 4.2mm axl

Wade | Acquirente verificato

  • Overall
  • Quality
  • Value

Customer Rated

Feb 26, 2014

I ended up with six of these. admittedly I crashed my quad and bent two of the props. But then today while hovering one of the motor shafts sheared off at the groove where the e-clip holds it on. Which by the way is where the other two bent.

Gerhard | Acquirente verificato

  • Overall
  • Quality
  • Value

Customer Rated

Sep 17, 2013

Good motor for this price. I run it in a flying wing with 1000mm(39.4in) wingspan and
460g(14.8oz) weigth. Prop 8x4(fold). 3S 850mA lipo. Goes unlimited vertical and has
around 5min motor runtime.

vaughan | Acquirente verificato

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Feb 20, 2013

Very nice motor although I couldn't slide the shaft through without fear of damaging it. It would need a thin firewall for attaching it behind the propeller.

  1. 1
  2. 2
File dei clienti
DIY Hex using 2725 motors Download [156]
Caricare un file

Registrati per caricare i file.
Per favore accedi o registrati per iniziare subito ad aiutare gli hobbisti!

Accessori