ADH300L Brushless Outrunner 1100kv

• Overall
• Quality
• Value

Jstehno

Mar 05, 2017

I powered a dynamo glider with it on 3cellsx1300ma with a 35mm spinner and a 8x6 folding prop 5g servos ,12.75 oz weight fantastic performance with balance at 1/4 wing chord. Happy with the results. PS I bought another Dynamo glider.

• Overall
• Quality
• Value

Certified Buyer Rated

Apr 01, 2014

Muy buen motor lo tengo un planeador de 600grs y lo lleva sobrado

• Overall
• Quality
• Value

Certified Buyer Rated

Feb 19, 2013

Don't be fooled by the lack of a brand name. An extremely modest little motor.

• Overall
• Quality
• Value

Customer Rated

Feb 01, 2013

Very efficient motor. Use these props only when on 3s.


8x4 electric direct drive or 8x4.3 slow flyer.

If you go 9inch, go to only 9x5 electric direct drive, not slow flyer! The gws 9x5 is max you should go on 3s.

• Overall
• Quality
• Value

Customer Rated

Jan 23, 2013

This motor is extremely powerful, very smooth running and responsive. I have no regrets with this purchase. However, the shaft broke off when I crashed under power. I can't yet find a replacement shaft. This is a good motor for the price.

• Overall
• Quality
• Value

Customer Rated

Mar 29, 2012

This motor is a great 2s motor. I used mine with 9x4.7sf prop 350 3s 15c, and 620 3s 15c, but when I upgraded to a Nanotec 850 3s 25/45c the motor BURNT OUT. Remember the higher the cell count the smaller the prop to get the same watts. That being said I ordered 2 more motors and some 2s Nanotec 850 2s 25/45c batteries and 9x4,7sf props.

• Overall
• Quality
• Value

Customer Rated

Sep 02, 2011

I have put given motor ADH300L Brushless Outrunner 1100kv on Kinetic 600. When I begin use it I will glad use it. Power is good . Kinetic is fly as bullet.

After few flyes I notice what controller begin hots and as a result 18A controller is burn. I disassemble motor and see what rotor brush stator , on stator furrow. This is because of poor fastening rotor with axis motor and bad metal material of rotor, hole is knock. Axis is not bent. Axis swinging in rotor.

Good motor as idea, but poor materials and poor quality.

I disappoint. Not recommend buy it.

• Overall
• Quality
• Value

Customer Rated

Aug 10, 2011

I have put given motor ADH300L Brushless Outrunner 1100kv on Kinetic 600. The axis has been turned concerning regular position. It is necessary to pierce deepening in an axis under the screw a fixing rotor.

Holes have approached ideally. Flies Kinetic with this motor very well, draft suffices for launch vertically upwards.

The controler 18A is heated with the given motor, I have put turnigy 30, it isn't heated

ADH300L Brushless Outrunner 1100kv Kinetic 600. . .

• Overall
• Quality
• Value

Customer Rated

Aug 01, 2011

I bought 2, used one to replace a geared 5:1 brushed 280, the other to replace a geared 5:1 brushed 370. This motor is about half the weight of the motors ithey replaced. Used a 25 amp brushless esc (I already had them) This motor likes 3s with a 9.47sf prop the best about 7000rpm, 120 watts about 21 oz thrust. 3s 10.47sf prop about 5000 rpm, 155 watts, 20 oz thrust and gets a bit too hot (for me). Mine had the second e-ring grove so I could put the shaft out the other side. Support the hub near the shaft when pressing out the shaft or you will have to get 2 small v block and a dial indicator to straighten the bell.

• Overall
• Quality
• Value

Certified Buyer Rated

Jul 05, 2011

Very good motor! Prop GWS 8x4 3s-610mAh, with flying time about 6 minute. The punch is higher when using 30C