New Items Forum
Registrati

Prezzo totale

0,00 €

Carrello 0 Carrello 0 Loading...

Freccia 4.3g / .8kg / 12sec Servo Micro

Freccia 4.3g / .8kg / 12sec Servo Micro

Shipped From:
  • USA
  • Global
QTY:

Now save risparmia 0,00 € 0,00 €

3,38 €
Stato:
Disponibile
Peso:
25 g
SKU:
BA-TS-43
WANT FREE SHIPPING? Click here to find out more!
Tensione di alimentazione 4.8V 6.0V
Velocità 0.12sec / 60oNo carico corsa
momento torcente 0.7kg.cm (9.71oz.in) 0.8kg.cm (11.1oz.in)
angolo di funzionamento 40 ° / un impulso lato viaggiare 400usec

Il peso netto di questo servo è 4.3g.
Può anche essere ricostruito in uno più chiaro.

Il peso netto di questo servo è 4.3g. Può anche essere ricostruito in uno più chiaro. Con il servo-chassis inferiore rimosso o usando la spina JST, il peso può essere ridotto a 4.0g. Utilizzare il filo smaltato per collegare, il peso può essere ridotto di 0,8 g. Totalmente, il peso può essere ridotto di 1.1g, e, infine, si ottiene un servo solo a 3.2g.

  • SKU BA-TS-43
  • Brand Blue Arrow
  • Peso (g) 25.00
  • Lunghezza 90.00
  • Larghezza 9.00
  • Altezza 70.00
  • Coppia ( kg) ( min . 0.01kg ) 0.80
  • Velocità ( Sec / 60deg ) 0.12
  • A ( mm ) 27.00
  • B ( mm ) 20.00
  • C ( mm ) 24.00
  • D ( mm ) 9.00
  • E ( mm ) 27.00
  • ( Mm ) F 15.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

mad little survos do what you want nice and smoothe and quick

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

mad little survos do what you want nice and smoothe and quick

petit servos efficace en indoor.

subit du 3D extreme pendant une saison sans probleme plus cela devient difficile...

je le recommande

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

petit servos efficace en indoor.

subit du 3D extreme pendant une saison sans probleme plus cela devient difficile...

je le recommande

I bought 2 of these to try. Firstly they are fitted with a normal JR plug and wiring is normal.
I changed my plugs as I have a PA-09 Crimper and lots of patience. There are however adapters available if you use a FrSky VD5M Rx like I do.
Initially I put them on my servo cycler as I like to run them for 10 minutes or so before I install them. I a bit was worried as they were very jittery even on different ms settings. However when I plugged into my FrSky Rx they were very quiet and no problems at all.
They are also the first servos I have ever had that get quite hot and very quickly. I was running them at 4.8 volts. They seemed quite OK but I wouldn't fit them in anything that required some duration.
I would not buy any more of these as there are better ones available but they will suit my intended purpose at this time.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I bought 2 of these to try. Firstly they are fitted with a normal JR plug and wiring is normal.
I changed my plugs as I have a PA-09 Crimper and lots of patience. There are however adapters available if you use a FrSky VD5M Rx like I do.
Initially I put them on my servo cycler as I like to run them for 10 minutes or so before I install them. I a bit was worried as they were very jittery even on different ms settings. However when I plugged into my FrSky Rx they were very quiet and no problems at all.
They are also the first servos I have ever had that get quite hot and very quickly. I was running them at 4.8 volts. They seemed quite OK but I wouldn't fit them in anything that required some duration.
I would not buy any more of these as there are better ones available but they will suit my intended purpose at this time.

I put this little servo in an rc car that i converted from cheapie 35mhz controls to a proper rc drifter. This little servo has taken so many impacts with the wheel jamming hard over as a drive shaft popped out and yet it's still fine. Not one stripped tooth. Really an impressive servo to say the least and I would certainly buy it again for small foamies or whatever I can hack together next.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I put this little servo in an rc car that i converted from cheapie 35mhz controls to a proper rc drifter. This little servo has taken so many impacts with the wheel jamming hard over as a drive shaft popped out and yet it's still fine. Not one stripped tooth. Really an impressive servo to say the least and I would certainly buy it again for small foamies or whatever I can hack together next.

j'en ai pris 6

je les utilise dans des parflyer cap232 et sukhoi 26

super permomant

rapport qualit prix imbattable

vous hestitez encore ? pas la peine foncez

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

j'en ai pris 6

je les utilise dans des parflyer cap232 et sukhoi 26

super permomant

rapport qualit prix imbattable

vous hestitez encore ? pas la peine foncez

Small but tough servo.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Small but tough servo.

Just received 3 of these servos and checked them via my servo checker. They run smoothly and quietly, however, the centering is erratic. Basically, when at full throw either side, and you go back to neutral on the servo tester, the servo rotates back toward center but stops past center clockwise. Then over the next 10-15 seconds the servo 'steps' back toward neutral in 4-5 separate steps finally stopping near neutral. So, from my viewpoint, not usable in any situation where you are expecting reasonable centering.

Don

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Just received 3 of these servos and checked them via my servo checker. They run smoothly and quietly, however, the centering is erratic. Basically, when at full throw either side, and you go back to neutral on the servo tester, the servo rotates back toward center but stops past center clockwise. Then over the next 10-15 seconds the servo 'steps' back toward neutral in 4-5 separate steps finally stopping near neutral. So, from my viewpoint, not usable in any situation where you are expecting reasonable centering.

Don

Good servo for shockflyers. Same power as hxt-500 but some lighter.I kove those transparent housings.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Good servo for shockflyers. Same power as hxt-500 but some lighter.I kove those transparent housings.

Great servos, or a few more than you wamt just in case, I had one burn. But still do the job. Thanks HK.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Great servos, or a few more than you wamt just in case, I had one burn. But still do the job. Thanks HK.

Nice Micro Servo's, fast enough for small gliders. I use them in the Versus DLG.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Nice Micro Servo's, fast enough for small gliders. I use them in the Versus DLG.

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. 6
Customer files
subaru Download [898]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save