Il Dolphin Jet è grande divertimento in un piccolo pacchetto! Con il suo basso prezzo, la costruzione di schiuma ultra-resistente EPO e di essere Plug and Fly, il Dolphin Jet offre un ottimo rapporto e divertimento ad un prezzo non si può battere!
La semplicità e la praticità sono stati tenuti in considerazione nella progettazione di questo velivolo. Offre un portello di batteria magnetica facilmente rimovibile, bullone su un pezzo ala e fori di raffreddamento sagomati per il vano batteria.
Ancora più importante, il Dolphin Jet vola buono come sembra, come EDF di un principiante che non può essere battuto. Questo modello dispone di un inviluppo di volo ampio - è altrettanto felice zippare lungo a tutto gas in quanto è crociera a potenza ridotta. E 'anche acrobatico consentendo loop, rotoli e per qualsiasi altra mossa acrobatica di base si può pensare!
Grazie al suo sistema di potere pre-installato brushless EDF e servi, si può volare il vostro Dolphin Jet in pochissimo tempo! Senza colla è richiesto per il processo assembley a tutti! Basta apporre il carrello di atterraggio e la coda in luogo, aggiungere il ricevitore e la batteria, avvitare l'ala e andare!
Parlando del sistema di alimentazione, incluso è montare un motore supplementare spinta opzionale per coloro che hanno la possibilità di sperimentare con l'assunzione di video o micro FPV'ing loro Dolphin.
Ultra-resistente costruzione in schiuma EPO
fori di raffreddamento di grandi dimensioni per il vano batterie
Preinstallato brushless sistema di alimentazione EDF e servi
Apertura alare: 1.010 millimetri
Lunghezza: 890 millimetri
Peso di volo: 700g
Motore: 4500kv Brushless Outrunner
ESC: 40A w / BEC (installato)
Servo: 9g x 4 (installati)
supporto motore pusher opzionale
4 canali TX / RX
1800-2200Mah 3S Lipo
What can I say. Went together in about 30 minutes. The push rods for elevator and rudder were a bit on the long side but were easily removed, shortened and a new Z bend put in place. I am going to use this as my first EDF before it gets converted to a pusher and has FPV gear fitted.
This plane should never have been made.
In the same way as jets, ducted fans are only suitable for fast planes. On slow planes they become inefficient. The Dophin is a ducted fan on a very slow plane, and as such does not make much sense. A lot of whining noise, low speed, and a battery pack that is soon exhausted.
No aerobatic capability, due to the flat underside of the airfoil.
To make the aerodynamics even worse, instead of nicely tapered trailing edges on wings and stabilizers, the Dolphin wing has 7 mm thick, box-like trailing edges. As if the thing does not have enough drag already.
In an effort to improve the speed, I cut 22 cm of the end of each wing and also shortened up the horizontal stabilizer somewhat. Right after take-off, the impeller from the ducted fan unit flew off. Consequently the plane lost all power and crash-landed into the stony ground next to our airstrip. Not too much damage, could easily be repaired, except for the ducted fan unit which would probably have to be replaced.
However, I am not spending any more time or money on this plane - it is heading for the bin!
A plane with potential. Well written (by comparison) instructions. The plane even flys well... until the grossly out of balance EDF explodes from vibration.
I'll now have to buy a quality EDF to make it fly, luckily when the EDF self destructed, after during the 3rd flight, the parts all stayed in the housing and none wee thrown free.Good, smooth, hard foam quality plus a nice little motor in a compact body, but let down by an absolutely dreadful fan - seriously out of balance & scraping against the outer casing. Overall it has the potential to be a decent edf model but check all components before flight as they may be loose or faulty. The supplied aileron Y-lead was a dud on mine. Remove & reglue the landing gear mounts before flight.Perfect beginner EDF. I went from a bixler 2 (First RC plane) to this and it just fly beautifully. it has made me fall in love with EDF. Awesome flight envelope.Great little plane that you can just put in the boot of a small car & fly almost anywhere.So easy to fly & does what its told.The only thing i found was that the motor only lasted a couple of hours before it burnt out,so a pusher motor was fitted & this has made it very reliable with enough power for aerobatics & long flight times.I bought this plane to give a try to FPF with an EDF plane. I tested it today (1st time i tryed an EDF plane), and this plane is great for FPV ! I used a 2Ah 45C bat, 500mA for video, 400mw 1.3G. It's not very powerfull, but far enough for FPV. It's very stable, very easy to control and it flies splendidly well. I like it !Great second airplane.
Watch this movie...
AREA15 mark2 team in ISRAELI bought this model a while ago but have only just been able to start using it due to a problem with battery connecters, HK have shown a list of batteries available to buy with this model but make sure if you are buying either of said batteries check that you have an adapter to convert the standard red block connection on the models speed controller to the yellow connection on the battery. they are very cheap and easy to get from HK themselves.
However, this model is a joy to be honest, you can use the large over wing format to simply glide the model through the air with minimal thrust or go all out and use the power provided by the fan unit to rule the skies. I have had a few incidents with this model yet it has always stayed in one piece and taken the hit. Since growing in confidence with this model I have been able to perform most 3D aerobatics and even had it fly knife edge along the ground it really is a model for beginners all the way up to pros.hi well it doesnt get any easier than this to learn how to fly EDF super easy to fly,and super stable,no problems putting it togeather,over all a good entry into EDF....