Ti pneumatici al pensiero di costruire il vostro prossimo 320 quad? Vuoi per un telaio formato PNF 320 con tutte le funzionalità di un Multirotor fai da te e di più? Il DYS 320 PNF Multirotor risponderà un grande sì a tutte queste domande!
Il DYS 320 PNF quadcopter ha tutte le funzionalità e la flessibilità di una cornice fai da te e la facilità d'uso di un PNF.
L'ultima offerta DYS incorpora qualità BE motori brushless serie, con licenza di bordo aperta pilota di controllo di volo CC3D (pre-tuned), inumidito piastra di isolamento fotocamera, regolatori di velocità BLheli e un design telaio pieghevole che si piega ordinatamente nella custodia in dotazione.
Il controller CC3D Flight fornisce una sensazione di incisività quando vola tricopters, quad, hexcopters, octocopters, e gli aerei ad ala fissa anche ed è stato appositamente selezionato per questa quadcopter PNF per portarvi una piattaforma stabile eccellente dritto fuori dalla scatola.
Il software di controllo a terra (GCS) fornisce un modo semplice per programmare la scheda tramite una connessione USB. Ogni scheda è stato pre-incamiciato in sintonia con il firmware più recente in modo da impostare il vostro quadcopter avrà pochissimo tempo.
Il DYS 320 PNF è fornito completo di un set completo di oggetti di scena, adattatori dell'elica e tutte le rifiniture di pregio.
• formato PNF aggiungere il ricevitore e via al divertimento
• controller 20A Opto BLHeli velocità
• Potente DYS BE motori della serie 2300kv
• Sistema di controllo di volo CC3D pre-tuned
• Open Cloud pilota configurati e pre-tuned
• Telaio pieghevole portatile (fibra di carbonio Full)
• caso pratico trasporto inclusa
• struttura in fibra di carbonio pieno Estremamente resistente
• Supporto parti intere
Base ruota: 320 millimetri
Motori: DYS BE1806 2300kv (preinstallato)
ESC: 20A opto BLHeli (preinstallato)
Props: 6x3 (preinstallato)
FC: CC3D (preinstallato)
5 ~ radiocomando 6ch
batteria 1300 ~ 2200 3s
FPV marcia opzionale
quad is nice, but no manuals at all, and it is not ARF at all, connected CC3D board and libre Pilot, configred radio inputs, but no output to motor ESC,
spent all evening online to find out that you have to use vehicle setup wizard in order to
make it work,
so not so plug and play,
quad is nice and fly ok, but order lot of spare props if you are new with quads like
me.this was my first racing quadcopter and it was the most fun i have had in a long time. it is so easy to setup and flys like a dream. I have only used it with point of view. but from what i can guess it works great with fpv.
with the many crashes i had being a first timer it stayed together very well, because it has folding booms it absorbs the impact of the fall and of course i have broken 20 props in the first 3 days of flying but that's me :D
works best with a 2200mah battery i could get 15 minutes with this with out compromising on power.
the only big complate it the landing legs, they made them out of carbon fibre along with the rest of the quad which was a STUPID idea, because carbon fibre is stiff as hell and i was scared to death to put them on let alone taking them of to get it in to the case.
good for beginners
tough and sturdy
easy to setup
easy to work with
hard to reach usb port
stupid landing legs
To order other items correctly, detail information is necessary.
Connector size for battery should be mentioned.
And a little bit detail assemble manual should be necessary.
Due to too stiff landing feet, now I cannot assemle them to carbon frame.I was really looking forward to this quadcopter when I've placed an order in January 2016. The delivery was quick and I was setting it up in open pilot in no time. HOWEVER, after going through all of the setting I found that one of the motors was twitchy. After back and forth emailing following online chat sessions HK sent me a replacement motor. The motor took over a week to get and it was a different colour (ok - not a big issue). HOWEVER the new motor didn't fix the problem! after soldering the new motor to the ESC, it still had the same issue!!! Finally, after spending about 2 hours with the HK online service chat, I've sent the quadcopter back to the warehouse (AT MY OWN EXPENSE!!) for replacement. Finally at the beginning of April (yes - APRIL!!!) I received the quadcopter that took off for 2-3min until it crashed. The FC lost power for some reason (while everything else had the power supply). After removing and connecting cc3d board via the usb I've noticed a hot spot and identified BAD SOLDERING that was shorting the board. Managed to remove the fault with the solder iron and now the quad is flying again. So what can I say - I don't think anyone should go though the same experience... the expectation is that the product that you pay for just works!Fit to my 3D cameras which I put in front of the frame. It look like an ant when I put VTXs with 2 antennas on top. Nice frame with case, so I can easily bring it anywhere without worry.Great little quadcopter for someone who doesnt want to build or worry about that part. Downside, when the ESCs go almost impossible to change out. The replacements that HK has are NOT a direct replacement, as you need to ask them about the new pin layout. Great price when the drop it to 50pcnt off sale price, but get it while its on sale, the sale typically ends pretty quick. The feet are extremely hard to snap on in the beginning, and annoying that you need to take them off each time to fit back into the case they designed for it (you would think they would make it fit).I have had this product for about 3 months it is my second quad this thing is great i have had some hard crashes with it and it still keeps flying great
out of the box easy set up and fly
loads of features
props are larger than stated
needs additional struts/posts
has a week spot on bottom plate by esc slight cracking if crashed hard
i would recommend it to my friendsgood little quad just the esc are part of the frame so have fun replacing them when time comes
file di clienti
dys 320 Scaricare ora [1436kb] 3d printable Head for props... in case you lost them Scaricare ora [705.94Kb] 3d printable Head for props... in case you lost them Scaricare ora [278.69Kb]