L'apparenza inganna. Questo outrunner è circa due volte la dimensione di un motore campana towerpro e oscilla un puntello molto più grande. Il suo motore utilizzato su alcuni di Art-tech nuovi kit aereo, che è testiment alla sua durata, facilità d'uso e qualità.
Il DT700 oscillerà un 11x4.7 SF puntello bene, per la produzione di più di 900g di spinta.
La sua grande per foamies GWS più grandi o piani parkfly.
Tensione richiesta: 11.1v
Capacità della batteria consigliata: 1300mAh +
Suggerita Prop: 10x4.7, 11x3.8 o 11x4.7
Max assorbimento di corrente: 13A (con il puntello 11x4.7)
Spinta max: 900g +
Corrente a vuoto: 1.2A
Albero: 4M (adatta perfettamente alla Towerpor / GWS SF puntelli lenta Fly)
Lunghezza totale: 77mm
Kv: 700rpm / v
Viene fornito con il supporto, come mostrato nella immagine
Rapporto di prova.
Abbiamo usato questo outrunner per alimentare l'una di Arte-tecnologia Pitts. Eseguire con un 1300mAh 3S1P 20C pacchetto, BESC 18A e 1147 GWS / Towerpro prop, le Pitts Art-tech correvano bene. Eccellente tasso di salita, anche se non hoverable, e con gli orari dei voli 13minute o più, siamo rimasti molto colpiti.
Un outrunner molto efficiente per lenti modelli volanti fino a .15 dimensioni.
Kv ( rpm / v )
Correnti Max (A)
Potenza ( W ):
Lunghezza B ( mm ):
Can Lunghezza D ( mm )
Max Tensione (V )
Albero A ( mm ):
Unit Weight (g):
Diametro C ( mm )
Lunghezza totale E ( mm )
Resistenza ( mh ):
very powerful bell motor, i ts almost equal in performance with a 35xx motor 920k, except that its half the price , also it can handle 4s easily, if 10-12`prop-=25amb esc
if 13 prop= 30 a escUsing this motor with a 30 Amp car ESC for an ROV project. So far preliminary tests are working nicely. It produces quite amount of thrust with my 57mm boat props, while submerged. the only problem I've had is that the set screws in the base seem to strip fairly easily, and I've had to drill an indent to keep the control wires from coming loos and flopping around.It's a good product. It works as it should be.
Two thumbs up. I would like to recommend it to all user.cheap work well and very efficient. the one and only down side is I have had 2 out of 4 have magnets come loose. I hope hk can in prove on their quality of products.These motors are ok for scratchbuild multirotors, but you will soon find they are a bit sluggish. You need to epoxy the wires which I am sure has been stated, but I ruined two motors before I did it correctly. I used Amazing Goop for ease. I have these on an h-quad, but they make a lot of vibration. I think all bells have that as they have such a small support, but large bell. For the price I'm sure you can find better motors that spin freely and have no need for modification.Good motors ....for the price....the issue is you can't really tighten props as if you try to screw the props too tight the shaft has a tendency to slip and cause the end ring clip to push against the bottom bearing causing the motor to run like its a bit jammed...gummy feel...I would go for the zip tie method to mount props....better bearings would be great....and neater windings would make this a killer deal....I don't think patrons would mind paying a couple of dollars more for this...all in all it is a great motor for a cheap not so trusty multicopterSuperb item to use in all RC stuff. Just safe peace of mind that you have a tad better item in your gear. Buy with confidencegood motor, altough winding is not the best quality.
If you crash your plane and shaft bends, there is no replacement parts for it.best brushless motors for my projects period, I have too many of them now.I have four of these DT700 motors and have used them on a tricopter preceding the quadcopter. I used these with the 11x4.7 sf props. They are good motors for the money but are a bad long term investment. They do what you want in the short run but if you are looking to go out and fly a multicopter and not worry about having a motor bearing go bad or the set screw loosen during flight or the balance being off, I would advise not to buy these motors.
If your going to build a multicopter, buy durable long lasting motors that will keep you on the flying field instead of in the workshop. Buy a quality set of motors. quality motors will most likely cost around $20-$30 per motor, especially if your using looking to get aerial footage and have a lot of expensive equipment on your multicopter. This may seem steep and I'm sure people will attest that their DT700 or DT750's work great, and good for them, but your going to spend the money either on a replacement or on bearings which will total to about the ammount of quality motors.
file di clienti
better_way_for_screws Scaricare ora [30kb] DT700 on homebuilt Karbon-X Frame Scaricare ora [278kb] DT700 on homebuilt Karbon-X Frame Scaricare ora [287kb] Custom motor mount Scaricare ora [126kb] No File Name Scaricare ora [48kb] Winding1 Scaricare ora [847kb] Winding2 Scaricare ora [754kb] Winding3 Scaricare ora [772kb] Measurement with 1245SF prop Scaricare ora [11kb] DT700 vs L2210-1650 data set Scaricare ora [24kb] DT700 vs L2210-1650 data set Scaricare ora [24kb] No File Name Scaricare ora [74kb] No File Name Scaricare ora [48kb] DT700 ROV thruster 4.19 lbs 5A Scaricare ora [512.70Kb]