Diventa fornitore Blog Nuovi oggetti
Registrati

Prezzo totale

0,00 €

Carrello della spesa 0 Carrello della spesa 0 Loading...

HKPilot Mega 10s Power Module Con XT60 Connettori

Generating Links

HKPilot Mega 10s Power Module Con XT60 Connettori

Prezzo:

Now save risparmia 0,00 € 0,00 €

21,68 €
Già acquistato Discontinued Product

Please continue searching for a similar product.
SKU:
387000052-0
Spedizione gratuita? Clicca qui per saperne di più!

Il modulo di alimentazione HV HKPilot incorpora sia un modo per alimentare il HKPilot e accessori, così come la tensione della batteria e la corrente rapporto di nuovo al HKPilot per i dati di registrazione e di telemetria. Questo può essere visto nel log memorizzati della HKPilot o vivere con un collegamento radio telemetria. Tutto attraverso un cavo a 6 pin singolo e strettamente incluso quello che soddisfa direttamente il connettore / PX4 / APM del HKPilot. Le uscite regolatore di commutazione 5.3V a bordo ad un massimo di 2.25A, e può essere utilizzato fino a 45Volts (10S LiPo) e ad un massimo di 90 ampere. Il modulo di alimentazione è pronto per l'uso con connettori XT60 pre-montati, e ridurre avvolto per la protezione.

Nota: Il modulo di alimentazione è valutato a 2,25 ampere per alimentare il HKPilot, ricevitore e periferiche (GPS e la radio telemetria) SOLO. Per potere utilizzare un servo ESC con un BEC adeguata o un autonomo BEC collegato al bus di uscita, e rimuovere il ponticello 1 di isolare le due linee di alimentazione.

Specifiche tecniche:
Tensione di ingresso MAX: 45V
Max rilevamento della corrente: 90A
Uscite di commutazione del regolatore: 5.3V a 2.25A max
Connettore: 6 poli cavo Molex si collega direttamente al connettore HKPilot / APM / PX4 'PM'
Tensione e misura della corrente configurato per: 5V ADC

include:
DF13 6 posizione del connettore 150mm
HKPilot Power Module con XT60 Connettori

* Nota: Il riferimento alla APM si riferisce al progetto ArduPilot, una famiglia di autopiloti open source basato sulla piattaforma informatica open source Arduino, sviluppato da 3DR e la comunità open source. Si compone di una scelta di ArduPilot Mega (APM) di elettronica e una gamma di versioni di software libero per i veicoli diversi ed è governata da una creative commons licenza open source.

* Nota: Questo non è un prodotto di marca originale Arduino.

  • HK Pilot Mega Accessories
Carica video

Registrati per caricare video, per favore accedi o registrati

Temi
Ordina per
Argomenti più recenti
* Nickname:

* La tua risposta:


Si prega di inserire il testo mostrato nell'immagine nel campo sottostante
*Codice di verifica:
Annulla
Invia
Pubblica un nuovo argomento
* Nickname:

* Il tuo argomento:



Si prega di inserire il testo mostrato nell'immagine nel campo sottostante
*Codice di verifica:
Pubblica argomento

Registrati per scrivere recensioni, per favore accedi o registrati

GlassKnees | Acquirente verificato

  • Overall
  • Quality
  • Value

Seems To Work Fine

Apr 21, 2019

I bought this while building another Tarot 650 Ironman - the previous one crashed during its 2nd test flight when the controller suffered a brownout. I was using 6S power with an APM module that was rated for 6S. This time around I decided to try this one, but I'm waiting delivery of a 6S lipo so I won't know for sure until I test under a full 6S charge, but so far it seems to work using a 4S lipo.

Walter F | Acquirente verificato

  • Overall
  • Quality
  • Value

Customer Rated

Jun 30, 2016

The connector going to the Pixhawk is the wrong connector (minor pin differences that prevent the connector from going into the board; the side rails and back tabs). There might be a way to shave it down, I tried, but finally pulled the connector off of an old 3DR Power Module and replaced the one on this Power Module. The wire crimped ends are the same for both so it only took a few minutes.

I haven't tried it yet at 9S, but assume that it works if I don't update this post.

| Acquirente verificato

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Mar 15, 2016

I purchaed 2 for my 2 quads and they are well built. Measures voltage and current accurately on HKpilot Mini.

| Acquirente verificato

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Mar 08, 2015

Very well constructed. Only niggle is the thinner wires as they seem fragile. I used heat shrink to stiffen the lead up covering partially the little connectors as well. Powered my HKpilot Mega with no issues! Remember to remove the jumper on the FC if using this! Doesn't heat up and seems efficient! Worth it's purchase!

| Acquirente verificato

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Mar 04, 2015

better quality than previous stuff from hk. all soldered well

| Acquirente verificato

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Mar 02, 2015

Works, but the connector comes loose easily

| Acquirente verificato

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Feb 21, 2015

very good, work well, very easy to use, you are worth a try. the price is very affordable. i use to my APM . thanks

File dei clienti
387000052-0-56855.doc Download [400]
Caricare un file

Registrati per caricare i file.
Per favore accedi o registrati per iniziare subito ad aiutare gli hobbisti!