New Items Forum
Registrati

Prezzo totale

0,00 €

Carrello 0 Carrello 0 Loading...

HKPilot Mega LED Driver Consiglio 12V (4 canali) (APM)

HKPilot Mega LED Driver Consiglio 12V (4 canali) (APM)

Shipped From:
  • Global
QTY:

Now save risparmia 0,00 € 0,00 €

4,20 €
Stato:
Disponibile
SKU:
387000046-0
WANT FREE SHIPPING? Click here to find out more!

Questo facile da usare portato bordo di driver è progettato e configurato per l'esecuzione di indicatori LED esterno dal Mega HKPilot o APM. Si può facilmente controllare di 12V ha portato fino a 700mA dalla A4 ~ 7 pin sul tuo APM controllore di volo compatibile. 12V indicatori ad alta visibilità esterna a LED per le armi a motore, lo stato del braccio, GPS, e bassa tensione possono ora essere facilmente controllato con questo deve avere accessorio controllore di volo.

Specifiche:
Tensione di ingresso: fino a 12 V
Uscita: 700mA
Peso: 5.3g
Canali di LED: 4

* Nota: Il riferimento alla APM si riferisce al progetto ArduPilot, una famiglia di autopiloti open source basato sulla piattaforma informatica open source Arduino, sviluppato da 3DR e la comunità open source. Si compone di una scelta di ArduPilot Mega (APM) di elettronica e una gamma di versioni di software libero per i veicoli diversi ed è governata da una creative commons licenza open source.

* Nota: Questo non è un prodotto di marca originale Arduino.

  • SKU 387000046-0
  • Brand H-King
  • Capacità ( mAh ) -
  • Peso 18.0000
  • Lunghezza 30.00
  • Larghezza 10.00
  • Altezza 30.00
  • HK Pilot Mega Accessories
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Easy to setup and does exactly what it is suppose to.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Easy to setup and does exactly what it is suppose to.

Great little board. Built flame wheel quad with HK Pilot Mega. Used four green / red LED strips for the arms. Connected the driver board input connection to the pilot mega inputs. Connected the very small power wires to the power distribution board. Great light display whin the quad is powered up.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Great little board. Built flame wheel quad with HK Pilot Mega. Used four green / red LED strips for the arms. Connected the driver board input connection to the pilot mega inputs. Connected the very small power wires to the power distribution board. Great light display whin the quad is powered up.

using this in combination with strip lights makes it easier to know whats happening. im using it for Arming, GPS might add a 12v buzzer as well

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

using this in combination with strip lights makes it easier to know whats happening. im using it for Arming, GPS might add a 12v buzzer as well

Used with 4x 3-LED long RGB-strips, one Red, one Green, one Blue and one White. Works great, and apparently on lower voltages too (~9 V) if you prefer dimmer LEDs, feeding with 3S should work, maybe even 2S if you'd need it? Hardware information: The chip is a Texas Instruments ULN2003A Darlington transistor array, datasheet can be found by searching for "uln2003a.pdf", seems like it has the capability to drive up to seven loads.
Downsides: The 12V input wires seem a bit flimsy for 700mA.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Used with 4x 3-LED long RGB-strips, one Red, one Green, one Blue and one White. Works great, and apparently on lower voltages too (~9 V) if you prefer dimmer LEDs, feeding with 3S should work, maybe even 2S if you'd need it? Hardware information: The chip is a Texas Instruments ULN2003A Darlington transistor array, datasheet can be found by searching for "uln2003a.pdf", seems like it has the capability to drive up to seven loads.
Downsides: The 12V input wires seem a bit flimsy for 700mA.

Great board. It came without instructions,but I soldered some test leds and figured out outputs.I use it on my s500 quadcopter - apm 2.5.2 from HK. Led strip(6x smd led) on each arm of frame. Just set parameter "LED_MODE" to 107(default is 9). I have gps lock blue led. When battery voltage is low red leds are flashing. Firmwavre is AC 3.2 rc7.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Great board. It came without instructions,but I soldered some test leds and figured out outputs.I use it on my s500 quadcopter - apm 2.5.2 from HK. Led strip(6x smd led) on each arm of frame. Just set parameter "LED_MODE" to 107(default is 9). I have gps lock blue led. When battery voltage is low red leds are flashing. Firmwavre is AC 3.2 rc7.

No instructions came with mine. The video is too general to be useful. Please supply a wiring layout or smple setup so that people can use these.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

No instructions came with mine. The video is too general to be useful. Please supply a wiring layout or smple setup so that people can use these.

Customer files
Ignore my horrible soldering! ;) Download [1238]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save