Dipartimento Funzione Pubblica Saturn F3P Ultralite EPS coperta 3D Aereo 920 millimetri con motore (Kit)

• Overall
• Quality
• Value

Customer Rated

Jun 05, 2014

Flying with 10 amp plush ESC, 500 mAh Zippy compact lipo's and using HXT500 servos.

Very well packaged. Carbon rods have stickers attached giving their length. The full colour manual clearly shows where each rod needs to go so you can't go wrong. Mine needed 20 grams of lead in the nose to balance to recommended CG, but I may remove some lead when I get more into 3D.

Only reason I've given it four stars for quality was mine was missing the landing gear baffles. No big deal and it looks fine without them.

Highly recommended.

• Overall
• Quality
• Value

Certified Buyer Rated

Nov 19, 2013

Just received it today.

Package is clearly serioux. All is carefully packed and tape to the box. If the plane is broken, then it means that the box is broken to. Building manual, propeler, Motor, building hardware (rods, wire...)



A very nice plane I can't wait to put it the air.



plusplus

• Overall
• Quality
• Value

Customer Rated

Oct 18, 2013

Nice little plane but build is not for a beginner. A little tricky and fiddly and instructions could have used a few extra detailed steps.

• Overall
• Quality
• Value

Customer Rated

Jul 08, 2013

I purchased this model the same time I bought the MXS. It came well packaged, no broken or missing parts. Assembly was straight forward and a lot easier than the MXS. I used foam safe CA on this model compared to 5 min epoxy on the MXS. I used the same set up as the previous model, Turnigy 1800 servo 3 pack, 10A HK ESC and a 370 Nanotech 2s battery. The pull/pull set up for the elevator and rudder is a bit tricky, but is a good system once it is rigged. This kit is much better made than the MXS. Depron is thicker and isn't as fragile. The covering is still loose fitting. Do not try to iron out the looseness it will warp any part you try it on. Run up was very nice, no evil noises or malfunctions. Power was perfect for the model, will hover just over 1/2 throttle. Flying couldn't have been easier. It is slightly larger and heavier than the MXS, but wouldn't recommend flying outside if there is much of a breeze. Inside it flew briliantly. Only very minor trim was required and slow flying was very easy. I was very comfortable with it after only a couple of flights. I didn't have any issues with it so far. I'd recommend this model over the MXS, but I like them both, thanks again Hobbyking...

• Overall
• Quality
• Value

Certified Buyer Rated

Jul 06, 2013

magnifique avion indoor, tres joli avec son entoillage transparent.. la legerete n'est pas transcendante car il faut compenser le manque de matiere par du carbone. mais tres reussi cote esthtique !!! et vol vraiment bien...

• Overall
• Quality
• Value

Customer Rated

May 05, 2013

Great indoor plane flys very well and slow without damping boards. The film covering needed checking over as it had lifted on the hinged surface. With a iron turned down to 10pcnt quick test on a edge run the iron over the lifted surface to stick the film down again. I ran the iron over the leading edges to be 100pcnt. Great job Hobby King used all reconvened parts in purchase 192grs with battery.

• Overall
• Quality
• Value

Customer Rated

Apr 20, 2013

No Regrets 3D plane; Very lite ; Fantastic to learn all maneuvers without fear ; Nothing it can't do . Added an extra carbon fiber flat rod at edge of wings and top and rudder top ( in case of inverted landing) . Excellent characteristics with 420mAh battery .. cG at aft of recommended in manual for 3D maneuvers. See uploaded second video in Video section

• Overall
• Quality
• Value

Certified Buyer Rated

Feb 28, 2013

great plane today i will fly it for first time