Prezzo totale

0,00 €

Carrello della spesa 0 Carrello della spesa 0 Loading...

Dipartimento Funzione X-Car 13,5 Accendere Sensori per motore Brushless 2600Kv

Generating Links

Dipartimento Funzione X-Car 13,5 Accendere Sensori per motore Brushless 2600Kv

Prezzo:

Now save risparmia 0,00 € 0,00 €

33,46 €
Già acquistato Discontinued Product

Please continue searching for a similar product.
SKU:
S2030-6003
Spedizione gratuita? Clicca qui per saperne di più!

Il Dipartimento Funzione X-Car Sensori per motori brushless offrono prestazioni eccezionali ad un prezzo incredibile. Caratterizzato da una anodizzato CNC qualità finire questi motori bene come vanno! I tempi regolabile permette per la messa a punto le prestazioni del motore mentre il sensore assicura una start-up lisce e accelerazione. I motori Dipartimento Funzione X-Car Brushless fanno un grande aggiornamento per il 1 / 10th brevi Camion del corso, passeggini o vetture turismo.

Specifiche:
Può Dimensione: 540
Attiva: 13.5
RPM / v: 2600kv
Sensored: Sì (standard a 6 ​​pin imbracatura)
Palo: 2
Tensione massima: 7.4 ~ 14.8V (2S / 4S)
Max corrente: 19A
Max Watt: 500W
Resistenza: 0.0361ohm
Corrente a vuoto: 0.6Amp
Dimensione stelo: 3,175 millimetri
Peso: 167g

Carica video

Registrati per caricare video, per favore accedi o registrati

Temi
Ordina per
Argomenti più recenti
* Nickname:

* La tua risposta:


Si prega di inserire il testo mostrato nell'immagine nel campo sottostante
*Codice di verifica:
Annulla
Invia
Pubblica un nuovo argomento
* Nickname:

* Il tuo argomento:



Si prega di inserire il testo mostrato nell'immagine nel campo sottostante
*Codice di verifica:
Pubblica argomento

Registrati per scrivere recensioni, per favore accedi o registrati

Khilra | Acquirente verificato

  • Quality
  • Value
  • Overall

Customer Rated

Aug 30, 2012

after 2 years:

This motor is still running strong. I ran it a long time on 4s in a 1/10 2wd sct, and it worked very well, actually too powerfull on 4s. I even ran a short time on 6s (not recommended as the motor is only rated at 4s) the sct is now setup for track running on 2s at 1:9,0 gearing, and it works very well. It is not as powerfull as 4pole motors, but it is smooth, and suits rwd sct trucks well at ~30mph. For higher speeds you should go for the 10,5T. This motor is cheap, reliable and has good power. Honestly, i am impressed, thought it would break down by now. Definetly recommended for use in 1/10 light offroad vehicles (rwd) and onroad.

Marko | Acquirente verificato

  • Quality
  • Value
  • Overall

Customer Rated

May 04, 2012

Nice looking motor made with average quality materials and assembly.

Considering the power of the motor it depends a lot on weight of the vehicle, surface that you run on it, the tires and the way of the driving. I am preparing the table with comparison of characteristic from 13,5T to 6,5T. I will publish as soon as it will be finished.

This motor is like as it is prescripted. I even measured much higher current draw.

Sensor plate went off after few drives, so now I can use it only like sensor less motor.

Khilra | Acquirente verificato

  • Quality
  • Value
  • Overall

Certified Buyer Rated

Aug 05, 2011

Recieved this motor mising 2 screws leaving the entire sensor plate loose. After fixing it the motor worked just perfectly.

Used it in a 2wd 1/10 SC truck on 4s lipo. Loads of power and very smooth. Amp draw was below 50 and temperatures never exceeded 60 degrees celcius with modest to hard driving. Very good motor on 4s lipo

| Acquirente verificato

  • Quality
  • Value
  • Overall

Certified Buyer Rated

Jul 13, 2011

Very strong at low rpm, running cold and quiet.

AfroNek | Acquirente verificato

  • Quality
  • Value
  • Overall

Customer Rated

Apr 14, 2011

I installed this motor in my Axial Honcho and all i can say is it hauls ass :p I'm running this motor off of a mamba max pro and bought a novak sensor wire to replace the one that never came in the box. I have a 17t pinion on it and using a 3 cell lipo, I have a hard time controlling the truck with anything more then 1/4 throttle witch is way to fast for anything crawling related. So far after about an hour of abuse this motor has nuked a metal spur gear and broken an axle with barely any effort while staying cool to the touch, I will defiantly be buying another for my other project and recommending it to friends.

Caricare un file

Registrati per caricare i file.
Per favore accedi o registrati per iniziare subito ad aiutare gli hobbisti!

Accessori