New Items Forum
Registrati

Prezzo totale

0,00 €

Carrello 0 Carrello 0 Loading...

KINGKONG 260 FPV corsa Drone Plug & Play (Red)

KINGKONG 260 FPV corsa Drone Plug & Play (Red)

Discontinued Product

Please continue searching for a similar product.
Peso:
969 g
SKU:
426000028-0
WANT FREE SHIPPING? Click here to find out more!

Il team KINGKONG hanno fatto di nuovo. Usando il loro popolare telaio 260 FPV hanno aggiunto un grande pacchetto di attrezzi per fare un ottimo Plug and Play pacchetto completo con la macchina fotografica e video FPV TX.

Questo Multirotor è alimentato dal KINGKONG Forza 200 Multirotor guida set attrezzature. Il kit ha tutto il necessario da un controllore di volo sintonizzati mini CC3D pre al fino al Spironet antenna.

I motori sono KINGKONG 2204-2300KV (CW e CCW) alimentato da KINGKONG 12A OPTO BLHeli ESC di. Con un UBEC (5v 3A) il potere di PPB. 6040 eliche saranno accelerare il ritmo.

Vi è una fotocamera preinstallato FPV e video, TX quindi basta sintonizzarsi sul canale e ottenere volare. La fotocamera FPV è inclinato in modo da vedere dove si sta andando, quando la gara è in funzione.

Proprio al fine di garantire che i concorrenti sanno dove siete c'è striscia di LED luminoso eccellente nella parte posteriore come questa sarà l'unica parte vedranno.

Questo imballaggio eccitante non solo è la parte, ma vi darà ore di divertimento corsa al giusto prezzo.

Caratteristiche:
• in fibra di vetro unibody completamente modellato telaio rinforzato
• Kingkong 2204-2300KV Motors (CW e CCW)
• KINGKONG 12A 2-4S OPTO BLHeli ESC di
• KINGKONG 5V-3A UBEC
• Potenza e video quadro di distribuzione con XT60
• Mini CC3D regolatore di volo
• 6040 Eliche (CW e CCW)
• FPV telecamera CMOS 1000TVL
• 200mW 5.8GHz Audio / Video Transmitter
• 5.8GHz circolare polarizzata Spironet Antenna
• fotocamera Azione monte
• Modulo Super LED luminoso (Assicurarsi che la concorrenza sa che sei tu più prendendo loro!)

Specifiche Telaio:
Passo: 260 millimetri
Peso: 138g (telaio nudo)
Materiale: Nylon + Fiber

Specifiche motore:
KV (RPM / V): 2300KV
Tensione: 7.4-14.8V (2-4S LiPoly)
Spinta max: 440g
Numero di poli: 12N / 14P
Elica: 5 "-6"
Pozzo del puntello: 5mm
ALBERO MOTORE: 3mm
Diametro: 28mm
Lunghezza: 31,2 millimetri
Peso: 26g
Spaziatura di fori: 16 mm o 19 millimetri M3

ESC Specifiche:
Tensione in ingresso: 7.4-14.8V (2-4S LiPoly)
Constant: 12 Amp
Burst: 20 Amps (5 sec max.)
BEC: No BEC, solo OPTO
Dimensioni: 50x16x6mm
Peso: 7.5g (con fili)

UBEC Spec:
Tensione in ingresso: 6V ~ 28V / DC (2-4S LiPoly)
Tensione di uscita: 5V
Ripple: Costante: 3 Amps
Dimensioni: 53x17x7mm
Peso: 12g

Specifiche della macchina fotografica:
Formato: PAL
TVL: 1000
Sensore: CMOS
Tipo di lente: F2.0 / 2,8 millimetri (IR-CUT)
Tensione in ingresso: 5 ~ 12V DC
Angolo di vista: 120deg

Video TX Specifiche:
Modulate: Wideband FM Modulate
Formato video: NTSC / PAL
Impedenza di uscita: 50 Ohm
Potenza di uscita: 23 ~ 24dBm
Canale: 32CH
Tensione di funzionamento: 7V ~ 24V
Corrente di alimentazione: 190mA
Temperatura di funzionamento: -10 ~ 85
Video Larghezza di banda: 0 ~ 8.0 MHz
Frequenza portante audio: 6.5MHz
Video Livello di ingresso: 0,8 ~ 1,2 Vp-p
Impedenza di ingresso video: 75 Ohm
Audio Livello di ingresso: 0.5 ~ 2.0 Vp-p
Audio impedenza di ingresso: 10K Ohm
Connettore: RP-SMA
Dimensioni: 40 x 23 x 8mm
Peso: 10g (senza antenna)

canali:
Banda A: 5865, 5845, 5825, 5805, 5785, 5765, 5745, 5725
Banda B: 5733, 5752, 5771, 5790, 5809, 5828, 5847, 5866
Banda E: 5705, 5685, 5665, 5645, 5885, 5905, 5925, 5945
Banda F: 5740, 5760, 5780, 5800, 5820, 5840, 5860, 5880

include:
1 x 260 KINGKONG
20 x 6040 Pro (10CW + 10CCW)
1 x Antenna Spironet
1 x adattatore di comunicazione software per PC CES
1 x camma di azione inumidito montare
pack 1 x Cavo
cravatta pack 1 x Cavo
set 1 x Antenna monte
1 x Cavo USB

richiesto:
5-6 Canale RX / TX
1300-2200mah 11.1V; 1000-1800mah 14.8V

  • SKU 426000028-0
  • Brand -
  • Capacità ( mAh ) -
  • Peso (g) 969.00
  • Lunghezza 360.00
  • Larghezza 70.00
  • Altezza 280.00
  • chasing planes @ pemac
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

What can i say,i am blown away by this quad. Having moved into this side of the hobby, i didn't want to spend a lot but i must say this performs like a much more expensive model. Had trouble hooking into Librepilot till i found an incorrect driver on my computer. Once that was sorted i was able to set this up using the Hobbyking FPV Racer profile.It's on bank one at the moment but as a noobie it's perfect, stable and responsive. If you are trying this sport for the fist time, you can't go wrong with this quad, top marks Hobbyking, definitely a winner.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

What can i say,i am blown away by this quad. Having moved into this side of the hobby, i didn't want to spend a lot but i must say this performs like a much more expensive model. Had trouble hooking into Librepilot till i found an incorrect driver on my computer. Once that was sorted i was able to set this up using the Hobbyking FPV Racer profile.It's on bank one at the moment but as a noobie it's perfect, stable and responsive. If you are trying this sport for the fist time, you can't go wrong with this quad, top marks Hobbyking, definitely a winner.

Fun quad!! This is my first racing quad, and although a little nervous about how to set everything up it turned out to be very straight forward. I downloaded the Libre-Pilot GCS software (available at: https://librepilot.atlassian.net/wiki/display/LPDOC/Downloads), and prebound my Spektrum satellite receiver with a primary receiver instead or going through the painful binding process. Once bound you plug your satellite receiver into the front left port and go through the Libre-Pilot wizard to setup and calibrate. It's that simple. Video worked great and aircraft flies awesome.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Fun quad!! This is my first racing quad, and although a little nervous about how to set everything up it turned out to be very straight forward. I downloaded the Libre-Pilot GCS software (available at: https://librepilot.atlassian.net/wiki/display/LPDOC/Downloads), and prebound my Spektrum satellite receiver with a primary receiver instead or going through the painful binding process. Once bound you plug your satellite receiver into the front left port and go through the Libre-Pilot wizard to setup and calibrate. It's that simple. Video worked great and aircraft flies awesome.

Very good racer for price.
If you are starting with fpv racer it's a good choice.

Here a video of my first flight with a fpv (and my kingkong by the way) :

https://www.youtube.com/watch?v=gTBqk9C_GM8

Very cheap and easy to repair !

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Very good racer for price.
If you are starting with fpv racer it's a good choice.

Here a video of my first flight with a fpv (and my kingkong by the way) :

https://www.youtube.com/watch?v=gTBqk9C_GM8

Very cheap and easy to repair !

great frame for beginners and pricingonly problem is when you break a arm you have to pull it ll apart and does get a bit annoying after 2 or 3 crashes

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

great frame for beginners and pricingonly problem is when you break a arm you have to pull it ll apart and does get a bit annoying after 2 or 3 crashes

wow this thing is alot of fun

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

wow this thing is alot of fun

great quad .
it took some time to to make it fly with my aurora 9 system but at the end it's flying.
the tx is bul......
the quad fly fast and you find yourself loosing video very fast.
lucklly i found it lost in the fields only with the rear red light.
order fatshark 400mw tx for the future flights.
ilan

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

great quad .
it took some time to to make it fly with my aurora 9 system but at the end it's flying.
the tx is bul......
the quad fly fast and you find yourself loosing video very fast.
lucklly i found it lost in the fields only with the rear red light.
order fatshark 400mw tx for the future flights.
ilan

I recently got these at what was a great price and now they are even lower. I was skeptical at first but apparently these got a bad rep for reasons I don't experience. I did receive 1 that the rear LED bar was shorted out of the box and smoked out even with a smoke stopper installed. Good thing I ordered 2 sets of frames which came with and extra light bar. The original got so hot it popped a LED off. The other thing. This was my first time using a CC3D FC and it was a total nightmare to get it flashed and going as I wanted it.
Now for the rest of the story. I am truly impressed so far. Much like their props that have saved me tons of money, these 260 class UAV's are a fantastic value at their current price. Are there areas I modified before the first flight? You bet! Some like the vtx zip tie needed a bit of help. The antenna needed put through the rear hole and then supported by plastic mold or one could use hot glue. There are things they could have done better IMHO but again ... Try to build one half as good for the money. I found it impossible.

Unless it develops some kinda voodoo and flies apart, next few times out, I call it a winner in many ways. Or at the very least a sleeper value.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I recently got these at what was a great price and now they are even lower. I was skeptical at first but apparently these got a bad rep for reasons I don't experience. I did receive 1 that the rear LED bar was shorted out of the box and smoked out even with a smoke stopper installed. Good thing I ordered 2 sets of frames which came with and extra light bar. The original got so hot it popped a LED off. The other thing. This was my first time using a CC3D FC and it was a total nightmare to get it flashed and going as I wanted it.
Now for the rest of the story. I am truly impressed so far. Much like their props that have saved me tons of money, these 260 class UAV's are a fantastic value at their current price. Are there areas I modified before the first flight? You bet! Some like the vtx zip tie needed a bit of help. The antenna needed put through the rear hole and then supported by plastic mold or one could use hot glue. There are things they could have done better IMHO but again ... Try to build one half as good for the money. I found it impossible.

Unless it develops some kinda voodoo and flies apart, next few times out, I call it a winner in many ways. Or at the very least a sleeper value.

I really really wanted to like this quad. Almost everything is perfect for a beginner who doesn't want to learn how to design/build them all themselves, except the frame. The frames are so fragile its not funny. What are you going to do when you start out? Crash. I bought this kit, and the 2 replacement frame kit and I have already broken two frames from only light crashes. The worst part is that the weak point of the frame is near the motor, so when the frame breaks it tears the motor off the ESC, destroying the motor. This means I have had to replace the motors as well.

Every other component on the quad works really well and is value for money. Since the price has been dropped so much since I purchased it a few weeks ago it might actually be worth buying this for parts. I will continue to use the FPV camera and transmitter, motors, ESCs, FC, and props, but I will be transferring them over to a carbon fiber frame. Don't skimp on the frame like I did. Save money on any other component.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I really really wanted to like this quad. Almost everything is perfect for a beginner who doesn't want to learn how to design/build them all themselves, except the frame. The frames are so fragile its not funny. What are you going to do when you start out? Crash. I bought this kit, and the 2 replacement frame kit and I have already broken two frames from only light crashes. The worst part is that the weak point of the frame is near the motor, so when the frame breaks it tears the motor off the ESC, destroying the motor. This means I have had to replace the motors as well.

Every other component on the quad works really well and is value for money. Since the price has been dropped so much since I purchased it a few weeks ago it might actually be worth buying this for parts. I will continue to use the FPV camera and transmitter, motors, ESCs, FC, and props, but I will be transferring them over to a carbon fiber frame. Don't skimp on the frame like I did. Save money on any other component.

Excellent racing quad for this price range! Flies really good and is a awesome racing quad for beginners. Be aware though; there are no documentation at all in the box, so you'll have to spend some time getting to know it.

Couple of tips:
1. Download LibrePilot to set the quad up. Just use the vehicle setup wizard, and then the transmitter setup wizard afterwards and you should be good to go!
2. If you're using the taranis with the X8R module and want to use your SBUS-port, you get a cable in package that fits in the main port (the one in the back, on the right hand side of the FC), and that has 4 pins on the other end. From the outer side of the SBUS-port, you want to plug in the black wire, the red wire and then the yellow wire. You don't have to use the green wire, just hide it in the quad (or cut it w/e).

But all in all, a great quad at a great price :)

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Excellent racing quad for this price range! Flies really good and is a awesome racing quad for beginners. Be aware though; there are no documentation at all in the box, so you'll have to spend some time getting to know it.

Couple of tips:
1. Download LibrePilot to set the quad up. Just use the vehicle setup wizard, and then the transmitter setup wizard afterwards and you should be good to go!
2. If you're using the taranis with the X8R module and want to use your SBUS-port, you get a cable in package that fits in the main port (the one in the back, on the right hand side of the FC), and that has 4 pins on the other end. From the outer side of the SBUS-port, you want to plug in the black wire, the red wire and then the yellow wire. You don't have to use the green wire, just hide it in the quad (or cut it w/e).

But all in all, a great quad at a great price :)

A brilliant little quad, well built, good components and well finished. The camera and VTX are good and should be more than okay for close fpv racing/flying. The motors are powerful and pair nicely with the ESC's. The frame is very strong/sturdy and the PDB is also very good and nicely incorporated into the frame. The flight control board is okay, i would say it has some limitations as it is a CC3D and I don't know how long the support will last for openpilot but it can be swapped out at a later date. It is more than enough for beginners/intermediate flyers such as myself.

To flash the board you will need openpilot 15.2 (just go to openpilots website) plug it in and it has a set up wizard that makes it all really easy. Of course you will need to have a radio and spare receiver too. Overall really happy with this purchase but I would say you would need some existing experience with quads/openpilot.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

A brilliant little quad, well built, good components and well finished. The camera and VTX are good and should be more than okay for close fpv racing/flying. The motors are powerful and pair nicely with the ESC's. The frame is very strong/sturdy and the PDB is also very good and nicely incorporated into the frame. The flight control board is okay, i would say it has some limitations as it is a CC3D and I don't know how long the support will last for openpilot but it can be swapped out at a later date. It is more than enough for beginners/intermediate flyers such as myself.

To flash the board you will need openpilot 15.2 (just go to openpilots website) plug it in and it has a set up wizard that makes it all really easy. Of course you will need to have a radio and spare receiver too. Overall really happy with this purchase but I would say you would need some existing experience with quads/openpilot.

Customer files
Manual Download [2]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!