Prezzo totale

0,00 €

Carrello della spesa 0 Carrello della spesa 0 Loading...

Micro A-10 EPS Pusher Jet (PNF)

Generating Links

Micro A-10 EPS Pusher Jet (PNF)

Già acquistato Discontinued Product

Please continue searching for a similar product.
SKU:
A10PUSH
Spedizione gratuita? Clicca qui per saperne di più!

Questo Micro A-10 utilizza un motore brushless pusher che dà prestazioni fantastiche.
Quando prova volato dal team Dipartimento Funzione Pubblica, questo piccolo Warthog ha suscitato molto scalpore. Vola così bene che avrebbe pensato era 3 volte più grande!

I 2.5G servo di sono pre-installati e centrate, il Comitato brushless e motore sono anche pre-installato, il montaggio è veloce e il modello anche dotato di scala guardando sotto-trasporto per coloro che volano fuori piste pavimentazione. Un foglio di istruzioni a colori e foglio decal sono inclusi, come è un puntello e risparmiatore prop.

Specifiche:
Apertura alare: 556 millimetri
Lunghezza: 512 millimetri
Peso di volo: 155g
Materiale: EPS
Motore: C10 Brushless Outrunner
ESC: BEC 5A
Servo: 2.5gx 2
3 Channel, Thottle, alettoni, ascensore

Richiede:
Il proprio 4 canali TX / RX
400 ~ batteria 500mAh 2s Lipoly

Carica video

Registrati per caricare video, per favore accedi o registrati

Temi
Ordina per
Argomenti più recenti
* Nickname:

* La tua risposta:


Si prega di inserire il testo mostrato nell'immagine nel campo sottostante
*Codice di verifica:
Annulla
Invia
Pubblica un nuovo argomento
* Nickname:

* Il tuo argomento:



Si prega di inserire il testo mostrato nell'immagine nel campo sottostante
*Codice di verifica:
Pubblica argomento

Registrati per scrivere recensioni, per favore accedi o registrati

Libtekguy | Acquirente verificato

  • Quality
  • Value
  • Overall

Certified Buyer Rated

Jan 29, 2012

I got this free. Didn't really want it so I just grabbed the servos, motor and esc off of it.

fotod | Acquirente verificato

  • Quality
  • Value
  • Overall

Certified Buyer Rated

Jan 16, 2012

Looks is arguable but I got it as a freebie. Prop version flies better and longer than EDF. Also lot of cheaper in total (price plus shipping). It's an EPS materjal so not super crash resistant but it's light. That keeps the damage minimal. You can add some carbon in wing or fuselage for strenght.



Comes fuselage glued and all electronics and pushrods inside. Tiny ESC is at the back under the two canisters. No airflow inside the fuse but I don't know if heat will be an issue.

It has total 2 micro servos, one needs gluing/taping. No glue supplied but surely it needs some for assembly. Wing mounting plastic parts needs to be re-glued and one even few mm lower. So the wing doesn't fit snugly in stock situation. But anyway you have to re-glue some parts because they are glued weak in factory.



Canopy is held on with... nothing. U have to figure out some locking option - buy magnets or just rubber around the canopy. Under the canopy only battery fits so receiver goes in the middle where is very tight fit because of aileron servo. But some thin micro RX should even fit in da nose.

Two sheets of decals you can stick. Landing gear seems good and light. Elevator even has a carbon strip attached. No carbon in the main wing though.

FPVking | Acquirente verificato

  • Quality
  • Value
  • Overall

Certified Buyer Rated

Jan 09, 2012

I got one again as a freebie. One wing side little bent and cracked tip but glue and time fix it. Motor mounted little off - have to re-glue. Wing doesn't fit in very easy - looks like have to re arrange the mounting parts. Also re-gluing some parts is a must.

Elevator servo inside is double side-taped and totally loose. Reglue or retape.

Marking on prop says 4x2.5R. Two planes both came with NO propsaver (sealed bags). No option to put the prop on and have to purchase mount separately now. Motor shaft is 2mm. Prop inside hole is 4mm.

I think I found that fits, search HK for C10-Saver.

| Acquirente verificato

  • Quality
  • Value
  • Overall

Certified Buyer Rated

Jan 09, 2012

1 review sai:

I got the beast as a freebie. Fitting together good but u have to re-glue the plastic bits more stronger.

Battery connection is JST. Battery room is (mm): 95 lenght, 20 wide, 38-23 deep. I purchased (imo the best lipos for this plane) 2s 460mAh nanos. They are quite wide but fit nice but not right up in the nose. Removing some foam from underside of the canopy make the battery fit in the nose OK if needed. And the 500mAh zippy is same thing. I prefer 460mAh nano-tech over zippy. Same flight time, more power, longer life and lighter plane. Search HK for N460.2S.25

Caricare un file

Registrati per caricare i file.
Per favore accedi o registrati per iniziare subito ad aiutare gli hobbisti!

Accessori