Questo modello è caldo!
Una macchina digiro EPO 1.4m 3D; questo modello su larga scala sarà sicuramente attirare una folla in qualsiasi club e chiedere il pieno rispetto tra i piloti in 3D in tutto il mondo.
Lo schema caratteristico e la scala è l'ideale per l'orientamento. La MX2 è grande per un modello di EPO e sembra quasi il doppio una volta che è in aria. Il suo un colpo di vento per volare ed è molto capace 3D!
Il potente, pre-installato filatura 36-48 motore che larga scala e 3 puntello lama dà un sacco di spinta per la più selvaggia delle maneouvers, e il servo preinstallati di sono certamente all'altezza del compito. superfici di controllo generose dimensioni in combinazione con il peso leggero assicurano che questo è un vero performer così come tornitore testa. Pratico e facile per gli occhi, le ali sono staccabili per un facile trasporto, un grande baldacchino assicura un facile accesso al vassoio del Lipoly, viti ad alette e così via.
Apertura alare: 1.400 millimetri
Lunghezza: 1.290 millimetri
Peso di volo: 1900g
Carico alare: 50g / dm2
Motore: 42-48 Brushless Outrunner
ESC: 70A w / BEC
Servo: 2 x 9g, 2 x 17g
Tuo 4 ~ 6 canali TX / RX
2200mAh 4s Lipoly Batteria
Motorsize ( diam - o - cc )
Apertura alare ( mm ):
SaleWeight ( g )
Telaio / PNF / RTF ( mm )
IC / 2 : Elec:
This is a very well made model and flies like a dreamIch habe versucht dieses Modell zu einem vernftig fliegenden Flugzeug zu machen: leider ohne Erfolg, das Merial taugt einfach nicht. Es ist extrem empfindlich, bei etwas hrteren Landungen bricht es sehr leich komlpett durch. Die Flgelbefestigungen sind absolut untauglich, etc, etc. Nach viel Stunden und Reperaturen (und zugekauften Ersatzteilen) habe ich mich genug gergert und werde das Modell "entsorgen", auch wenn es am Boden immer noch sehr gut aussieht.
Sorry HK, ich bin sonst von vielen eurer Produkte sehr angetan!I got this as a gift for my son he is 42. So this is not for son who is a good modler. The instructions are useless and pictures are even worse. The small parts bag was missing many items. The paint on one single panel was bobbles no paint. Flying is good but the CG is very important. No Where in instructions is it providedNice looking model, pity the quality is crap, tail wheel a pain ,control rods to long, elevator rod to long by 15mm , wrongly labelled items. poor manual, screw hols filled with glue, wheel hubs have to be drilled out to allow wheel to spin , tight on bolt so when wheel turns it follows thread and locks up. rudder needs extra hinge, hope it fly's awesome after all the mods and work to get it built.Im going to be as real as possible on this plane. Stock setup will not 3D , the plane is too heavy for this. Flew mines today with a 2650 4s and when she got airborn as soon as i pitched the plane she wanted to snap on me (Wing tip stall) then i landed the plane and tried a lighter battery this time using a 2200 4s , Did much better but still had the snap problem when pitching the plane. Don't Believe what you see in the video in the description of this plane because it will not perform that way with some modifications.
1ST thing i would do is replace the wing spare with a lighter one because thats one problem for the wings. Weight is every important in a aerobatic plane. 2nd Replace the landing gear with carbon fiber lighter ones , these add extra weigt to the plane. 3rd Change out the tires and buy lighter ones. Those 3 items i mention should be replaced to make this plane lighter and fly better.
The stock motor and prop are good enough for this plane to do 3d with , did some testing before i took it out to the field. Other than that it flys pretty good , takes off fast. Just with they would make some changes to the plane and make it lighter.The tail piece on this one may arrive warped. The landing gear holes in the bottom of the fuse don't line up and have to be re-drilled before the landing gear can be re-attached. The landing gear wheels will bind-up and you may need to remove the wheels and remove some foam to allow the wheels to spin freely. The tail wheel arm will likely hit the tail/rudder and may need to be bent to fit. Mine snapped, even with heating first. I had to fabricate a new piece in the correct shape. It's easiest to do this with 2mm aluminium. The motor mount screws are over-tightened and not holding well in the wooden brace. You may need to swap them out for larger screws. The motor has no loctite on the bolts. You should unbolt it all and loctite it all in properly. The servos that come with it are not as advertised. They are full size units (41x20x37) of unknown make/model. They have lots of play and will need to be replaced before you fly, with better quality units, as the rudder/elevator will be too floppy.
Not a good product, but with some loving you can get it into reasonable shape.Great Plane Poor Prop Adapter. Build own one from DURALUMINIUM