Registrati

Product Finder

Impostazioni

Useful links

 
[["US","AU","GB","DE"]]
Registrati
Shipped From:
  • Global

SK450 Morto Cat "Defibrillatore" Power e A / V Scheda di distribuzione e Power Shield

SK450 Morto Cat "Defibrillatore" Power e A / V Scheda di distribuzi...

QTY:

Now save risparmia 0,00 € 0,00 €

22,00 €
Stock:
Peso:
463 g
SKU:
9171000236

Suggestion Box

Please let us know if you found any issues with this product listing.
We take our customer comments very seriously and in many cases our website modifications and product updates are a result of your comments!

Price War

If you've seen a product elsewhere for a better price, please let us know! HobbyKing pride themselves on offering the best price, so if there if you see something cheaper elsewhere, let us know!

Descrizione
prodotto

Abbiamo tirato fuori il defibrillatore e scioccati po 'di vita serio per la conversione del gatto morto! Lo stile Spider Quad-Copter era già impressionante con il suo angolo braccio ottimizzato e layout per una vista libera FPV dell'elica. E ora la progressione tanto atteso per una potenza integrato e scheda di distribuzione A / V e collegare di potenza schermati.

La nuova scheda inferiore ha piazzole di saldatura diretti per le linee di alimentazione del motore ESC proprio alla base delle braccia e potere "in" pastiglie situato direttamente sopra la batteria per ridurre al minimo il cablaggio. Ci sono connettore di alimentazione del sul frontale, posteriore e centrale per il vostro ingranaggio FPV e controllore di volo, tutti legati allo scudo potere che senza sforzo Supply un mercato regolamentato, filtrato e RF rumore schermato 5 volt a un enorme 3 ampere per il controller della fotocamera e di volo e 12 volt a 1 ampere per i più affamati di trasmettitori video. I connettori video nella parte anteriore e posteriore, inoltre, non solo fornire la tensione ma anche portano il segnale audio e video dalla parte anteriore fotocamera montata sul retro montato trasmettitore video. Questo aggiornamento ti consente di risparmiare peso, ripulire il layout e migliorare l'affidabilità, riducendo errori di connessione. Credo che questo Dead Cat dispone di 9 vite dopo tutto!

Caratteristiche:
• Distribuzione omogenea
• pastiglie di saldatura stile Wick
• trasmettitore integrato di cablaggio Fotocamera e video
Ingresso • 3 o 4 celle
• SMPS convertitore con schermo di protezione del rumore RF
• termica Protetto

Specifiche:
Tensione di ingresso: 8-16v (3-4 cellule LiPoly)
Peso: 142g
Uscita: 5V / 3A e 12V / 1A

* Nota la conversione gatto defibrillatore morti per la SK450 SK450 richiede il telaio e Dead conversione gatto correlati qui sotto.

Product
Specifications

Ulteriori informazioni

  • SKU:
    9171000236
  • Brand:
    N/A
  • Peso (g)
    463.00
  • Lunghezza
    375.00
  • Larghezza:
    30.00
  • Altezza:
    215.00
Community
Discussions
Rate&
Review

Scrivi la tua recensione

Only registered users can write reviews. Please, sign in or sign up

Quality
Value
Overall
I am completely happy with this, what a great product! This did wonders to clean my quad up! Some sort of schematic would have been nice however a quick check with my DVOM and I was off and running! This is a must have for the Deadcat frame!!!
Quality
Value
Overall
Quality
Value
Overall
great thing, saves a lot of cables

and makes it look cleaner
Quality
Value
Overall
Quality
Value
Overall
This is a must for your dead cat upgrade

making the whole upgrade look the bees knees
Quality
Value
Overall
Quality
Value
Overall
Fairly straightforward but I wish it came with documentation on what each connector does.
Quality
Value
Overall
Quality
Value
Overall
I was hoping this board would make the addition of a camera and Vtx easy and quick. Not so.

The connectors on the board are male 4 contact connections. It is very difficult to find female 4 contact connectors. I tried using 3 conductor female servo connectors without the outer sleeve. When installed there is not enough room for these connectors on the controller and battery connector and the connector will hit the top board.

The best solution is to remove all of these connectors and install header pins. Once this is done standard male servo connectors can be used. The 4th pin is for audio, which I did not use so the 3 pin connectors would work.

Somewhat disappointed as this created a lot more work than should have been necessary.

If the board would have had header pins. I would give 5 stars.
Quality
Value
Overall
Quality
Value
Overall
this is a great idea, too bad it will be useless if they ban fpv
Quality
Value
Overall
Quality
Value
Overall
So a friend and I are building dead cats. His is built and flying and after a hard landing the copper band for his ground circuit going to the defibrillator cracked and started pealing off. My frame hasn't been build because my filtered 12v to my video TX is shorted to ground out of the box. .......Not to mention his was nose heavy with a go pro 3 and a 3300mah 3 cell. So I ordered a 4000mah 3 cell because I have a heavier go pro 2 and ccd board cam for fpv but then ran into my electrical short when pinning out the board. I had high hopes for the dead cat but am having second thoughts now for sure.
Cheap lower defibrillator board.
Nose heave with a go pro sized camera. (With 3300mah)
Arms flex

Quality
Value
Overall
Quality
Value
Overall
I had bigger hopes for this. You have 5V in the front and 12V in the back and a just one extra pin intended for video between front and back. I would like to see both 5V and 12V front and back and some extra pins that I could use for whatever.



The defibrillator seems to output 10V on the 12V pin based on just a quick test with 3S.



Also note that the pins are FEMALE for everything. If they where male we could use the extra servo cables we have...



Connecting a Tarot 2D gimbal to this needs hacking. The defibrillator is in the way and the provided holes are not suitable for the Tarot. I opted to add a separate plate in between the deadcat and gimbal.
Quality
Value
Overall
Quality
Value
Overall
Totally agree, the idea is good, like the Black Sheep TBS Discovery product, but the difference is they give you hook-up pins and connectors. HK, at least give us a reference or source to find the pins we need. Come on HK, you have a good concept, follow it through and give your customers a complete product.......after all you require us to buy three different kits to get "one".
Quality
Value
Overall
Upload
Videos
  • Dead Cat PCB Board

Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Tag prodotto

Usa gli spazi per tag separati. Usa apostrofi singoli (') per frasi.