SU26-60IN

• Overall
• Quality
• Value

Somebody knew what they were ding when they built this airplane.It like the Zlinn 50L i bought off of you people.It flies really nice and the landing when you set up your landing it reminds you of a big goose landing,nice and stable.I had to cut the airle

Jul 08, 2018

Somebody knew what they were doing when they built this airplane.Its like the Zlinn 50 L i bought off of you people.it flies really nice and landing,when you set up your landing it reminds you of a big goose landing nice and stable.I had to cut the airllerons down it is much to high right now but it is other than that it is nice and i really mean nice.The RCGF motor i installed in it really runs nice.I yous Klotz bean oil with hightest gas.the engine is still breaking in.

• Overall
• Quality
• Value

Excellent all round value and quality

Jul 01, 2018

A further update,
While the plane can take two elevator servos, there is a wooden (light ply) elevator joiner and then you can use one elevator servo on either side of the fuse.
It flies really nicely on a 6s set-up. I have the SK3 5045 500Kv with a 16x8 Vox prop 100 amp Hobbywing platium esc and it has a ton of power. CG around wing spa, flies really well and is a capable 3D plane. Great value and looks good.

• Overall
• Quality
• Value

Sukhoi S26

Jun 26, 2018

Prompt delivery and in the most robust box I have ever seen!
Initially kit looks good, superb finish, elegant lines!
One wing cannot be fitted as one of the alignment hole was not drilled (Not a problem) Wood selection is poor! No wheels (No problem)
Beautiful engine cowl, nice C/F undercarriage.
I have built a number of similar kits so I do know what I am doing but the complete lack of any instructions leaves me a bit puzzled.
Should build up to be a very nice model but would not recommend it to an inexperienced builder as mods will be needed to produce a decent model which is spoilt by lack of instructions and poor quality control.

• Overall
• Quality
• Value

This plane looks good and is well made

Jun 09, 2018

The plane is well made and is very very light. The structure really suits an electric setup. I went for the Turnigy Aerodrive 5055-430kv motor with the Plush 100 amp esc. The propeller is the Dynam 17 x 12 carbon and it gives unlimited vertical. The battery is 6S 5000mA NanoTech that balances well. The control surfaces are huge and response is quick. The kit lacked wheels and a manual, I put the C of G just in front of the spar.

• Overall
• Quality
• Value

The workmanship on this airplane is really really nice.Right now i am locating the mortise cut for the control horns to be placed.The Zlinn 50l has a simular set up.Both are really nice ARFs.I plan on useing the NGH 17 gas in the Sukio or the RCGF 15 gas

May 09, 2018

The workmanship on this airplane is really really nice.Right now i am locating the mortise cuts for the control horns to be placed.The Zlinn 50L has a similar set up.Both are really nice ARFs.I plan on useing the NGH 17 gas in the Sukio or an RCGF 15 gas in my new Zlinn 50L i have not made up my mind yet?

• Overall
• Quality
• Value

Très bien

Mar 06, 2017

Finition pas mal il y a tous ce qui faut sauf le manuel. J'ai installer un Turnigy 26Hp-s 26cc jai du modifié le couple moteur pour mettre le carburateur arrière dans ce couple, jai installer 2 servos a la profondeur j'ai installer 1 lipo en réception et 4 nimh a allumage je n'ai pas eu de problème pour le centrage le model fait 3,2 kg je doit encore le tester en vol mais le moteur tire bien je suis assez comptent de mon achat pour le moment

• Overall
• Quality
• Value

Answer to my question

Jan 11, 2017

Further to my first post. The answer to my question is that this plane takes two elevator servos, so there is no joiner.

BTW all of the hardware is high quality.
Cheers

• Overall
• Quality
• Value

Looks Good Quality

Jan 11, 2017

Took delivery just now. Not double boxed but the box is super strong, so no damage. No instructions whatsoever, so only for experienced builders. Only thing I'm trying to figure out is how the elevator halves are joined/connected. There is no metal joiner that inserts into each of the two halves. There is a solid piece of ply about 150mm long by 10mmx5mm, so maybe that is what was intended to be used. I think I will go electric, I would have thought a 20cc petrol engine would be too much for this and make it way to nose heavy
Update later.