New Items Forum
Registrati

Prezzo totale

0,00 €

Carrello 0 Carrello 0 Loading...

TGY AerodriveXp SK Serie 28-36 750KV / 262W

TGY AerodriveXp SK Serie 28-36 750KV / 262W

Shipped From:
  • Global
Discontinued Product

Please continue searching for a similar product.
SKU:
SK-2836-750
WANT FREE SHIPPING? Click here to find out more!
TURNIGY AerodriveXp Serie SK
I motori AerodriveXP SK serie sono progettate per chi vuole il meglio della tecnologia per la loro outrunner / C aereo R. Tipicamente un miglioramento dell'efficienza di circa il 8-10% può essere visto sopra motori classificato simili. Questo è in parte dovuto al seguente;
Statore laminazioni: .2mm
Tipo di magnete: N45SH
Cuscinetti: doppio oversize (giapponese)
Modello: 750 SK28-36
Kv: 750rpm / v
Attiva: 11
Resistenza: 130m-Ohm
Idle corrente: 0.4A
Albero: 4mm
Peso: 80g
Potenza nominale: 262W
ESC: 25A +
conteggio delle cellule: 2-4
Suggerita Prop: 11x8 ~ 12x6



* Comprende il Monte e accessori adattatori prop (non mostrato)
  • SKU SK-2836-750
  • Brand -
  • Peso 110.0000
  • Lunghezza 0.00
  • Packaging Width 0.00
  • Altezza 0.00
  • Kv ( rpm / v ) 750.00
  • Correnti Max (A) 0.00
  • Resistenza ( mh ) 130.00
  • Max Tensione (V ) 14.00
  • Potenza ( W ) 262.00
  • Albero A ( mm ) 4.00
  • Lunghezza B ( mm ) 38.00
  • Diametro C ( mm ) 28.00
  • Can Lunghezza D ( mm ) 26.00
  • Lunghezza totale E ( mm ) 55.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Muito bom, com um spiner muito bom mesmo, recomendo

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Muito bom, com um spiner muito bom mesmo, recomendo

I was going to use these in a boat, the Kv is good, drives a 40 mm brass prop with ease on 11.1 volts in a 1.3 metre patrol boat hull excellent scale speed. draws 14 amps on a Raboesch 40 mm 3 blade prop.

They are noisy, the bearings are gritty and the bell is not concentric with the shaft, i get 0.5mm run-out, this means lots of noise and vibration especially at a certain RPM which must be a resonant frequency.
I can live with the bearings they were easily replaced but the bell run-out is not good enough

Sorry Hobby King but this motor needs better quality control

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I was going to use these in a boat, the Kv is good, drives a 40 mm brass prop with ease on 11.1 volts in a 1.3 metre patrol boat hull excellent scale speed. draws 14 amps on a Raboesch 40 mm 3 blade prop.

They are noisy, the bearings are gritty and the bell is not concentric with the shaft, i get 0.5mm run-out, this means lots of noise and vibration especially at a certain RPM which must be a resonant frequency.
I can live with the bearings they were easily replaced but the bell run-out is not good enough

Sorry Hobby King but this motor needs better quality control

Don't waste your time and money on this one.

It is very noisy.

When I speed up the motor without load.

The noise out with vibration.

It is looks like unbalanced.

I test the motor using 12x6 propeller only 133wattA11x6 propeller 0nly 132watt.

It is not a 262 Watt motor look like.

So the performance is quite low.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Don't waste your time and money on this one.

It is very noisy.

When I speed up the motor without load.

The noise out with vibration.

It is looks like unbalanced.

I test the motor using 12x6 propeller only 133wattA11x6 propeller 0nly 132watt.

It is not a 262 Watt motor look like.

So the performance is quite low.

Sorry but have to give this only 2 stars. Yes the motor works but that's about it! You can't use 3S because you get virtually NO power out of it and if you go up to 4S to get anywhere near 200watts or more they start to get VERY hot after only a couple minutes. I was gonna use this in a twin setup P-38 but found other motors. I have other SK motors and they've been fine, just don't waste your time and money on this one.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Sorry but have to give this only 2 stars. Yes the motor works but that's about it! You can't use 3S because you get virtually NO power out of it and if you go up to 4S to get anywhere near 200watts or more they start to get VERY hot after only a couple minutes. I was gonna use this in a twin setup P-38 but found other motors. I have other SK motors and they've been fine, just don't waste your time and money on this one.

Parameters of winding resistance for this motor, are incorrect.

I have two.. They are exactly equal.

Measured resistance is 185 miliOhm.

Motor is "star" type.

It is quite useless for any higher power.

I may suggest, not to try to exceed 10 amperes.

You may use 4s or even higher voltage... Anyway, for 80 gram motor it seriously underperforms, and it will burn if prop is too big.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Parameters of winding resistance for this motor, are incorrect.

I have two.. They are exactly equal.

Measured resistance is 185 miliOhm.

Motor is "star" type.

It is quite useless for any higher power.

I may suggest, not to try to exceed 10 amperes.

You may use 4s or even higher voltage... Anyway, for 80 gram motor it seriously underperforms, and it will burn if prop is too big.

This is perhaps the strangest motor I have ever used. I put it in an E-flite Mini Pulse with a 12X6 on 3s. It would barely fly it. When I tested other props on it, i had to go all the way to 14X7 to get adequate thrust. I ended up using 4s and 11X8 to get good performance.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

This is perhaps the strangest motor I have ever used. I put it in an E-flite Mini Pulse with a 12X6 on 3s. It would barely fly it. When I tested other props on it, i had to go all the way to 14X7 to get adequate thrust. I ended up using 4s and 11X8 to get good performance.

This is a good motor.Should be run on 4s for best performance.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

This is a good motor.Should be run on 4s for best performance.

Good motor, but a bit too heavy, The price is good !

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Good motor, but a bit too heavy, The price is good !

tres bons moteur.moto planeur de0,9Kg.alloy folding spinner 50mm.pales 12/10.rhino 1750-3s.planeur monte a la verticale

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

tres bons moteur.moto planeur de0,9Kg.alloy folding spinner 50mm.pales 12/10.rhino 1750-3s.planeur monte a la verticale

Indeed, wrote to avoid the review:

Engine bearings are not good, noisy operation.

Circuits mounted on the screws are long and meke, allen is now worn out.

Choose another engine waste of money.



verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Indeed, wrote to avoid the review:

Engine bearings are not good, noisy operation.

Circuits mounted on the screws are long and meke, allen is now worn out.

Choose another engine waste of money.



  1. 1
  2. 2
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!