Questo fa parte del towerpros nuova generazione di motori.
Miglioramento della qualità dei cuscinetti e l'albero, così come statore ottimizzato e disegno del magnete.
Dimensioni: 51mm diametro x 89,2 millimetri Lunghezza
Idle corrente: 1.2A
Recomended Lipo Config: 6-8 celle
Diametro albero: 6mm
Max Efficienza: 57A
Carico massimo: 72A
Max Power (W / 60): 1700
Suggerita Prop: 16x10
Motore dotato di lega robusto adattatore di montaggio piastra e ogiva mostrato (tipo pinza). vite senza testa e alberi di fermo possono essere allentate per invertire l'albero per il montaggio firewall differenti posizioni.
motor is a quqlity product with nice appearance and can swing a 17/10 prop with authority on 6cA 123's
I will fly this in a 7lb P40 WarbirdExcellent motor, same exact efficiency, size and performance as an AXI 4130-20.. used it to replace a burned up AXI in my 9.5lbs P51. See this thread for details:
With a 10s1p pack of Dewalt A123 cells and an APC 13*10 electric prop it used 43Amps at 28volts, 1200 watts. Simulation was pretty close to actual results, use Kv=352, Io=1.2A, Rm=99mohms... for the A123 lipos use voltage=3.35V, 8mohms resistance, 2300mah capacity. Excellent motor for the 60-90 size plane.Motor looks really nice. Put an APC 18x8 on with six Emoli cells. At 31 amps it was getting just over 5000 rpm producing over 7 pounds of thrust. With 6S 4400 mah I expect to go a bit faster but it is perfect for the five pound 3D job it is targeted for.
I mounted this motor on my Hanger 9 Funtana 100 X today and was very pleased with the power. My static test showed more than 1700 watts on an 8S 4000 mah battery at 60 amps swinging a 17x10 apc prop. The plane is 8.5 pounds so it should be balistic! Will be flight testing this week.I put this motor on a Sig HogBipe and with 6s2p A123's and of to the heavens I went. All I can say is no more AXI's for me. TowerPro motors are my choose of motors for now on. Top notch motors.Great motor, this thing cranksMight be a bit of overkill on a .46 size plane but pulls like a train on 7 a123 cells with a 15x13 prop. 40A at approx 17 volts = unlimited verticle!Ulrich, it is possible to mount it backwards.. loosen the two set-screws and the wheel collar and slide the motor shaft forward.. apply blue locktite and re-tighten set screws. It is a tight interference fit so you may have to gently tap it with a hammer to get the shaft to move.
Limit this motor to 1200 watts in a sport plane.Tested this motor with 6 Lipo cells and 8 cells.
With 6 cells and using an 16x10 APC Prop the motor had 6.000 revolutions by using 35 A
With 8 cells and a 15x10 glow prop it had 9.000 revolutions and draw 45 A.
Great motor, for good price, no backward mount possible if neededEcellent !
Mes mesures :
6S2P HXT2250, contrleur Pentium60 APC-E 16x8 30,5A 6060tr 640W
Forte bois 16x8 32,2A 6060tr 675W
MPX Bois 16x10 34A 5880tr 715W
8S2P HXT2200, contrleur Pentium 80HV APC-E 14x10 36A 7600tr 1000W
Grp bois 15x8 32A 8000tr 900W
Forte bois 16x8 42A 7100tr 1200W