New Items Forum
Registrati

Prezzo totale

0,00 €

Carrello 0 Carrello 0 Loading...

Turnigy Dlux 20A SBEC Brushless Speed ​​Controller w / dati di registrazione (2S ~ 4s)

Turnigy Dlux 20A SBEC Brushless Speed ​​Controller w / dati di registrazione (2S ~ 4s)

Discontinued Product

Please continue searching for a similar product.
SKU:
9192000026
WANT FREE SHIPPING? Click here to find out more!

Turnigy® Dlux SBEC CES hanno stabilito un nuovo punto di riferimento in termini di qualità e prestazioni, tanto che questo ESC leggero e molto versatile in grado di gestire fino a 6S e + 10A scoppio corrente con la massima tranquillità. Le numerose funzioni di programmazione e di logging dei dati offrono anche una versatilità di applicazioni raramente visto in un CES di questa valutazione. Tutti i CES Turnigy Dlux possono essere programmati tramite una scheda di programmazione o con il trasmettitore. Chiaro e facile da capire le istruzioni sono incluse.

* Ora con la registrazione dei dati visualizzabili quando utilizzato con la scatola di programmazione Turnigy Dlux.

Parametri di visualizzazione di registrazione dei dati:
Temperatura massima
Ambiente Temperatura
Max corrente
corrente Min
Max Voltage
Tensione Min
Voltaggio nominale
spento Tensione
Motor Run Time
Accensione Tempo
Motore Pole Numero
RPM Max Motor
tempi di errore

Spec.
Max Cont. Corrente: 20A
Max Burst corrente: 30A
Max BEC corrente: 2A
BEC Tensione: 5.5v
LiPo: 2 ~ 4S
NiMH: 5 ~ 12cells
Peso: 22grams
RPM Max (2 poli): 200,000rpm
Dimensioni: 51 x 27 x 11 millimetri
Motore spina: 3.5mm Femmina proiettile connettore
Batteria Spina: Nil

Caratteristiche.
Estremamente bassa resistenza interna
temperatura di funzionamento molto bassa
Sopra protezione di temperatura
APEC MOSFET (Taiwain)

Opzioni di programmazione.
Tipo di batteria: 2S ~ 4S
Avanti / indietro
soft Start
LV Tagliare Tipo (Ignora, ridurre la potenza, arresto del motore)
LV Tagliare impostazione (2,5 ~ 3,5 V con incrementi di 0,1 V)
Timing (Auto, medio, alto)
Switching (8,16kHz)
fabbrica di ripristino
Controllo RPM Attivo: On / Off (modalità Governatore)

Impostazioni predefinite.
Freno: off
Batteria: LiPo Rilevamento automatico
Bassa Tensione: 3.2V (spegnimento del motore)
Timing: Auto
Frequenza: 8KHz

Nota: scatola di programmazione ora disponibile, controllare gli elementi correlati qui sotto.

  • SKU 9192000026
  • Brand DLUX
  • Capacità ( mAh ) -
  • Peso 40.0000
  • Lunghezza 110.00
  • Packaging Width 7.00
  • Altezza 100.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

SimonK Firmware aufspielbar!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

SimonK Firmware aufspielbar!

Got this to go in my Radjet 800 (stock set up). It is just a shame that this ESC comes with such short wires.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Got this to go in my Radjet 800 (stock set up). It is just a shame that this ESC comes with such short wires.

Here's a late update to the previous review of the ESC:
Contacted HK CS to let them know the ESC wasn't working and they needed some "proof" of the failure. So I hooked all the electrical parts up and was getting ready to shoot a short video so the problem could be seen 'in action' as-it-were. Before I started the camera rolling the ESC started showing signs of life, the motor started spinning (under control of the servo tester) and then smoke and flames shot out of one end of the ESC. Whoops...
I forwarded photos (and a short video) of the damage and after a few more emails I received a full refund credit. I'm tempted to try another one but I'd like to read some success stories first.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Here's a late update to the previous review of the ESC:
Contacted HK CS to let them know the ESC wasn't working and they needed some "proof" of the failure. So I hooked all the electrical parts up and was getting ready to shoot a short video so the problem could be seen 'in action' as-it-were. Before I started the camera rolling the ESC started showing signs of life, the motor started spinning (under control of the servo tester) and then smoke and flames shot out of one end of the ESC. Whoops...
I forwarded photos (and a short video) of the damage and after a few more emails I received a full refund credit. I'm tempted to try another one but I'd like to read some success stories first.

Received my ESC last Tuesday (01/22/2013) and 5 days later had an opportunity to fire it up. First I connected it to my Turnigy Programming Box and even though the display on the box lit up, I couldn't get any setting info to show. Thinking maybe my box was too old and the firmware outdated, I went directly for a quick test with a 1450Kv motor, 3S Nanotech pack and my Hitec HFP-20 servo programmer (as a signal source). No beeps or any other signs of life came fourth from the 20A, dlux ESC. There was power present from the built-in SBEC but that's all. It's dead...

And what's with the conflicting specification regarding the number of series LiPo cells it can handle? Is the number 4 or is it 6? Somebody has to get this info consistent. It's rather critical!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Received my ESC last Tuesday (01/22/2013) and 5 days later had an opportunity to fire it up. First I connected it to my Turnigy Programming Box and even though the display on the box lit up, I couldn't get any setting info to show. Thinking maybe my box was too old and the firmware outdated, I went directly for a quick test with a 1450Kv motor, 3S Nanotech pack and my Hitec HFP-20 servo programmer (as a signal source). No beeps or any other signs of life came fourth from the 20A, dlux ESC. There was power present from the built-in SBEC but that's all. It's dead...

And what's with the conflicting specification regarding the number of series LiPo cells it can handle? Is the number 4 or is it 6? Somebody has to get this info consistent. It's rather critical!

Good ESC, I only did the programming with the programming box.
Easy to set up, also the cut off temperature can be programmed in a range from 90-105.
Very fine throttle response over the complete range.
Maximum cut of setting available is 3.2V on the one I have.

I took this one because of the data logging when used with Turnigy dlux programming box. Good to have data for an easy controll of the setup. I would appreciate the amps measuring with .1 steps, not only 5A or 15A for example.
Displaying the logged data works fine on the box.

For getting rough data (min / max. values) to check that the drive setup is in the correct range its OK. For detailed data on competition models I still prefer the SM-Modellbau data logger.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Good ESC, I only did the programming with the programming box.
Easy to set up, also the cut off temperature can be programmed in a range from 90-105.
Very fine throttle response over the complete range.
Maximum cut of setting available is 3.2V on the one I have.

I took this one because of the data logging when used with Turnigy dlux programming box. Good to have data for an easy controll of the setup. I would appreciate the amps measuring with .1 steps, not only 5A or 15A for example.
Displaying the logged data works fine on the box.

For getting rough data (min / max. values) to check that the drive setup is in the correct range its OK. For detailed data on competition models I still prefer the SM-Modellbau data logger.

No special comments. Just a ESC but together with its programing box, a nice and reliable combo.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

No special comments. Just a ESC but together with its programing box, a nice and reliable combo.

Lger, il faut maintenant tester sa durabilit

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Lger, il faut maintenant tester sa durabilit

very nice. .

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

very nice. .

Customer files
Programming with Tx instruction Download [58]
Programming with Tx instruction Download [58]
Programming manual (instruction) Download [208]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save