Turnigy e-drive 2210/30

• Overall
• Quality
• Value

Turnigy e-drive 2210/30

Mar 21, 2009

. .

• Overall
• Quality
• Value

Customer Rated

Jan 29, 2009

Tested 28 Jan 08 with Zippy-H 3S 11.1v LiPo and new APC-E props:



6x4 268g 11.95V 5.8A 69W 13470rpm 3.88 g/w

7x5 430g 11.56V 10.2A 118W 11250rpm 3.64 g/w

8x4 568g 11.45V 11.4A 131W 10620rpm 4.34 g/w

9x6 - g 11.20V 16.4A 183W 8835rpm 0.00 g/w



(accurate 9x6 thrust measurements not obtainable due to motor/bearing vibration)



1278 rpm per volt @ 12.25V

no-load current: 1.0A



price: 4/5

quality: 2/5

value: 3/5

• Overall
• Quality
• Value

Customer Rated

Dec 07, 2008

Great motor.



SETUP:

pack: A123 3S 1100mAh

ESC: OEMRC 25A



TESTS:

Propeller / Amps / Volts / Watts / RPM / P.S. / Trust



APC 8 x 3.8SF / 10.3A / 8.9V / 92W / 8700rpm / 50km/h / 470g



APC 8 x 6SF / 13.5A / 8.7V / 117W / 7500rpm / 69km/h / 540g



APC 9 x 4.7SF / 13.1A / 8.8V / 115W / 7900rpm / 57km/h / 630g



APC 9 x 6SF / 17.0A / 8.6V / 146W / 6400rpm / 59km/h / 570g



APC 10 x 3.8SF / 16.0A / 8.6V / 138W / 6500rpm / 38km/h / 700g

• Overall
• Quality
• Value

Turnigy e-drive 2210/30

Nov 14, 2007

Exelent motor!

Very good quality.

1700 3S LiPo, 25 Turnigy ESC and 8x4 APC prop give about 600g trust.

Motor shaft can be mooved to any side of the motor!

• Overall
• Quality
• Value

Turnigy e-drive 2210/30

Nov 14, 2007

Great motor.



SETUP:

pack: A123 3S 1100mAh

ESC: OEMRC 25A



TESTS:

Propeller / Amps / Volts / Watts / RPM / P.S. / Trust



APC 8 x 3.8SF / 10.3A / 8.9V / 92W / 8700rpm / 50km/h / 470g



APC 8 x 6SF / 13.5A / 8.7V / 117W / 7500rpm / 69km/h / 540g



APC 9 x 4.7SF / 13.1A / 8.8V / 115W / 7900rpm / 57km/h / 630g



APC 9 x 6SF / 17.0A / 8.6V / 146W / 6400rpm / 59km/h / 570g



APC 10 x 3.8SF / 16.0A / 8.6V / 138W / 6500rpm / 38km/h / 700g



GWS 8 x 4HD / 8.2A / 9.3V / 76W / 9700rpm / 59km/h / 460g



GWS 8 x 6HD / 9.3A / 9.1V / 85W/ 8500rpm / 78km/h / 480g



GWS 9 x 5HD / 12.0A / 8.9V / 107W / 8000rpm / 61km/h / 600g



GWS 10 x 6HD / 14.3A / 8.7V / 124W / 7400rpm / 68km/h / 730g



I replaced the CF2822 with this unit and now, I'm using on a 380g 3D foam plane with APC 10 x 3.8SF.



Highly Recommended.

• Overall
• Quality
• Value

I mad a mistake

Nov 14, 2007

Sorry - my previous review was for the Turnigy 2826-07 motor so ignore.



I have just installed this motor 2210 on a combat wing and it is great. Very smooth, good quaility. The prop adaptor that is supplied is a prop saver type. You simply cannot do better for the price and even solder terminals are supplied.

• Overall
• Quality
• Value

Great quality for the price

Nov 14, 2007

A really great motor that is a low cost substitute for the hyperion 3025 - 08. Some points to note are:- 1. The shaft was installed opposite to that shown in the picture - good for back mounting the motor. It looks like the shaft can be moved if required. 2. The backmount plate is quite a bit bigger than expected. It is 3mm thick with diameter of 64mm. It will be easy to reduce size to the standard 50mm if firewall is too small. 3, Magnets seem strong and 5mm shaft will match with hyperion prop adaptor. Standard prop adaptor is also supplied.

• Overall
• Quality
• Value

Great quality for the price

Nov 14, 2007

A really great motor that is a low cost substitute for the hyperion 3025 - 08. Some points to note are:- 1. The shaft was installed opposite to that shown in the picture - good for back mounting the motor. It looks like the shaft can be moved if required. 2. The backmount plate is quite a bit bigger than expected. It is 3mm thick with diameter of 64mm. It will be easy to reduce size to the standard 50mm if firewall is too small. 3, Magnets seem strong and 5mm shaft will match with hyperion prop adaptor. Standard prop adaptor is also supplied.

• Overall
• Quality
• Value

Good Motor Running Smooth

Nov 14, 2007

Nice motor and good material come with anything you need to install in aircraft. Good price I very like it.

• Overall
• Quality
• Value

Great quality for the price

Nov 14, 2007

Very good motor for this price. Only one mistake: motor shaft is wrong size.