Prezzo totale

0,00 €

Carrello della spesa 0 Carrello della spesa 0 Loading...

Turnigy EasyMatch G46 Series - albero di ricambio

Generating Links

Turnigy EasyMatch G46 Series - albero di ricambio

Prezzo:

Now save risparmia 0,00 € 0,00 €

2,48 €
Quantità:
Spedito da:
  • Global
Già acquistato
Ora di arrivo prevista: Nessun Orario Di Arrivo Previsto [ ? ]
Stato:
Ordine arretrato
SKU:
031000018
Spedizione gratuita? Clicca qui per saperne di più!

Turnigy EasyMatch G46 Series - albero di ricambio

Spec.
Lunghezza del pozzo: 76mm
Diametro albero: 6mm

attributeset-10
Close

Dimension Diagram Guide

  • attributeset-10

Close

Carica video

Registrati per caricare video, per favore accedi o registrati

Temi
Ordina per
Argomenti più recenti
* Nickname:

* La tua risposta:


Si prega di inserire il testo mostrato nell'immagine nel campo sottostante
*Codice di verifica:
Annulla
Invia
Pubblica un nuovo argomento
* Nickname:

* Il tuo argomento:



Si prega di inserire il testo mostrato nell'immagine nel campo sottostante
*Codice di verifica:
Pubblica argomento

Registrati per scrivere recensioni, per favore accedi o registrati

Kiwibob | Acquirente verificato

  • Overall
  • Quality
  • Value

Replacement shaft

Jan 28, 2022

Purchased G46 shaft and fitted it t=o the motor without any problems

David B | Acquirente verificato

  • Overall
  • Quality
  • Value

G46 back to life

Nov 20, 2021

Thank you HobbyKing for making this replacement shaft available, it has enabled me to repair a perfectly good motor and bring it back to life. Here’s an account of how I did it.
I needed to replace a crash-bent shaft in my G46 550kV motor. The grub screws came out without too much trouble but pulling apart the stator and rotor bell was a tough job because of the strong magnets. Once I had managed to pull them apart, I could not press (in my vice) the shaft out of the rotor bell. Possibly some thread locker had wicked its way from the grub screw along the shaft or perhaps it was a tight interference fit. Anyway, a friend recommended heating the rotor bell with a hot air gun on the principle that since it was made of an aluminium alloy it would expand more that the steel shaft and would therefore allow the shaft to be pressed out. Using strips of thin card wrapped around the body of the rotor bell, I created a protective jacket that was just under 4mm thick. The purpose of this was to minimise heating of the rotor bell’s body - I didn’t want to risk de-magnetising the magnets or weaken the bond of the glue holding the magnets in place. I put a few drops of water onto the top of the jacket to prevent it burning when heat was applied to the nose of the rotor bell. I used a hot air paint stripper gun to apply the heat and was then able to press the shaft out (in my vice), very easily. It looked like some thread locker had indeed wicked in between the shaft and rotor bell, so I carefully removed this with a small file.
The motor had three bearings, two off size 6x12x4 (MR126 ZZ) in the nose of the rotor and one off 6x19x6 (626 ZZ) in the stator. Since one of the nose bearing was damaged, I decided to replace all three, which I purchased from SMB Bearings Ltd, in Carterton, UK.
Using my digital caliper I compared the replacement shaft diameter with the original. Both were exactly the same. The replacement shaft was a tight fit, but it could be fitted by hand - no vice required. The motor is now working just as good as new.

Eric | Acquirente verificato

  • Overall
  • Quality
  • Value

Very slow delivery!

Dec 06, 2020

Very slow delivery

Rusty | Acquirente verificato

  • Overall
  • Quality
  • Value

Shaft

Nov 19, 2019

Good spare

Gary | Acquirente verificato

  • Overall
  • Quality
  • Value

Nice

Oct 03, 2019

Exactly as ordered

Caricare un file

Registrati per caricare i file.
Per favore accedi o registrati per iniziare subito ad aiutare gli hobbisti!