Progettato per essere uno swap diretta fuori per il vostro 0,40-0,46 cilindrata bagliore. Questo outrunner brushless fornirà più potere e con la sua alta efficienza, tempi di esecuzione lunghi.
Un motore di qualità, costruito appositamente per gli aerei progettati per volare con un motore .40 ~ .46 bagliore.Spec.
Batteria: 4 ~ 5 cellulare /14.4~18.5VRPM: 670kvCorrente max: 40ACorrente a vuoto: 10V / 3.9ACapacità di corrente: 55A / 15secResistenza interna: 0,04 Ohm
Peso: 303g (non compresi i connettori)
Diametro del pozzo: 6mm
4S ~ 5S Li-Po / 12 ~ 16 celle Ni-MH / Ni-Cd
12x8 ~ prop 14x10
Adatto per lo sport e scala gli aerei di peso da 4 a 7 libbre (1.8-3.2 kg).
Kv ( rpm / v )
Correnti Max (A)
Potenza ( W ):
Lunghezza B ( mm ):
Can Lunghezza D ( mm )
Max Tensione (V )
Albero A ( mm ):
Unit Weight (g):
Diametro C ( mm )
Lunghezza totale E ( mm )
Resistenza ( mh ):
Excellent value and great power. Use this motor in my Phoenix Tiger 40 with a 5s battery and 13/8 prop. It fly really well and has a excellent power band. After a 12m flight it's only luke warm.I installed this in a Phoenix Convertible 40 and run with an 85A Blue Series ESC and Turnigy4000MAh 30 C batteries. Flying weight is 2.775kg. Great performance and getting a safe 8 minutes flying time with throttle management and a little spare capacity.Put this on a 40 size Ultra Stick have had no problems yet. It was a great substitute for a power 46 motor.Guter Motor mit guter Performance. Eingebaut in einer SBD-5 Dauntless von VQ. Spannweite 1540 mm / 61.4 in, ~3,2 Kg /7.05lbs.
Lipo: Wellpower (Lindinger) 5S 4500 mAh 30 C 100pcnt geladen
Regler: 60A BlueSeries Brushless Speed Controller
Max 60.51A/100 pcnt Gas
Max 1145.76W/100pcnt Gas
Der mittgelieferte Prop-Adapter hat einen Wellendurchmesser von 10 mm
Mehr nach dem ErstflugGreat high quality and cost effective motor that runs great; I would recommend it to anyone interested,Fitted this in my kyosho spitfire this is a very good motor with lots of power. Had a master screw three blade prop 14 x 6 fitted made a lovely sound.This motor turns a Master Airscrew 11x6 three bladed prop at 9,900 RPM. I run this motor with a Turnigy 85Amp ESC (w/5A SBEC) and a Turnigy 5000mAh 40-50C four cell battery. After a 10 minute run, it's barely even warm. The only draw back is that the prop adapter is the collect type and huge. Not sure what the prop shaft size is but it appears to be about 9mm. It requires reaming of the prop larger than either my metric or standard reamers largest sizes. For about eight bucks you can get a Great Planes 6mm prop adapter which has a standard 5/16" prop shaft. Other than that, this motor is beautifully made with nice tight bearings. Since it's not working very hard on four cells it should last a long time. I'm definitely going to get at least one more.Hi !
I bought this motor specially for an Hangar 9 Piper Cub (1/5 scale) and it fits very well. With an APC thin 13x6,5 , and 3,4 kgs weight, I can fly around 15min with a 4S 4500mah Turnigy battery. Associated with Turnigy 60amp controler, that's just perfect.
Very good quality and very quiet in the air, I love to fly my Piper, a bit particularly due to that nice motor.
Thanks Hobbyking !I Tested this motor with a 12 x 6 Prop with
4S 3000mAh 20C and got 375 watts.
I am using this in my ARC Jupiter with this setup and works good.
what a powerplant!! im using it on a alfa40 and i get unlimited vertical with a 12x10 prop!!! 5 stars