Turnigy Distributore di potenza Min UBEC (giallo)

• Overall
• Quality
• Value

Super

Nov 08, 2017

Absolut super! Hab sie in meiner Cap232 mit 2,65m eingebaut, funktioniert alles wie es soll.
Achtung, wenn sie die Anlage mit 2S betreiben kann die Ausgangsspannung auf max. ca.6,8V erhöht werden, jedoch mit 3S auf die wie angegeben 9,3V oder so....
Was auch immer wieder zu Fehlern führt, es müssen immer 2 Akkus bzw. Lipos angesteckt sein damit das Teil richtig funktioniert!

• Overall
• Quality
• Value

Cheap Insurance

Mar 29, 2017

I have purchased 4 of these units now, 3 yellow 1 black, only because yellow was out of stock. I use these only for dual battery redundency and the fact if you have a switch failure it fails to the on. I dont care about no LCD all you need is a simple voltage checker with a Futaba plug to set servo voltage. I have also never used the ignition kill feature as I always use a RC Excell kill switch. I have not to this day been let down by 1 of these units and intend on purchasing another today.

• Overall
• Quality
• Value

Customer Rated

Apr 22, 2016

Top, fr den Preis unschlagbar !!! Betreibe eine 3m Bella damit vllig Problemlos. Spannung einstellbar, Zndung ber die Weiche ein und ausschaltbar mehr geht nicht TOP !!!

Warte das sie wieder kommt, brauche noch 2 Stck davon....

Bitte HK schnell wieder auffllen !!! :-)

• Overall
• Quality
• Value

Customer Rated

Oct 13, 2015

IT has not LCD SCREEN. IT HAS FAKE SCREEN. There is a Turnigy writing on the fake screen. Also a led is shining back side of the fake LCD. Another functions are ok. You can buy another version of this power distributor that it has almost the same functions from another stores cheaper than hobbyking.

• Overall
• Quality
• Value

Customer Rated

Aug 31, 2015

Seemed to be a great product, all worked as it should initially, after three flights, CDI kill switch stopped working, red light flashes indicating less than 4.2V input no matter what battery is connected and the switch is inoperable.
Fitted on a Yak52 with a RCG 26cc gas engine.

I will now have to purchase a CDI kill switch.

• Overall
• Quality
• Value

Customer Rated

Jun 13, 2015

Be careful to isolate this board from vibrations on the larger planes. My opto for the ignition control came loose from the board in my Sbach 34pcnt, 35cc, because I had the screws down too tight on the rubber grommet mounts. Bad solder joint. The ignition randomly shuts off (sometimes while in flight!). I'm going to isolate the board and receiver in foam and use Velcro to hold it in the plane. JohnnyB

• Overall
• Quality
• Value

Customer Rated

Oct 26, 2014

I have purchased 3 of the original 3 panel design panel units. I have installed them into 3 of my giant scale planes. The new panels are a single plastic box. They are easy to use and they performed as intended.
CAUTION!! One of the 3 panel design units failed and I lost all power on my 84 P-51. What I found was one of the 2 ribbon solder joints fail on the main BEC that is located on the bottom panel failed. I was able to repair the remaining units by removing the top 2 panels and repairing the ribbon solder joints. Make sure to get the solder to flow to both sides of the panel. It was a simple repair but why should we have to repair them to ensure we dont lose our planes.
Come on Hobby King Pick up your game!!!!
PS I havent used the new design yet but I do hope they have resolved the problems.

• Overall
• Quality
• Value

Customer Rated

Aug 15, 2014

This Bower box works Beautifully, But always remember to leave your assigned kill switch down when you turn on your transmitter and do this before powering up your Power Distributor, Then turn on the power distributor and your kill position will always be down to kill the CDI, This sequence is necessary unless you don't care where the kill position will be. This is a built in Safety feature to always start with the system in the kill position. Hope I made it clear to avoid confusion. Happy Flying ! Ron

• Overall
• Quality
• Value

Customer Rated

Aug 08, 2014

Great product awesome price for this product. Only one thing could be made better.... an voltage display fr the bec adustment or an DIP Switch with steps and not an potentionmeter...
But again an awesome Product.

• Overall
• Quality
• Value

Certified Buyer Rated

May 08, 2014

Muy buen producto... pero no es de 30A