Turnigy Servoless Attuatore per ingranaggi porta (90-120 dimensioni) - Unità servoless leggero che è adatto per entrambi i sistemi servoless e ritrarre l'aria elettronici, può essere azionato tramite il sequencer Turnigy Ritrarre / Gear porta (vedi articoli correlati qui sotto) per quasi tutte le configurazioni, viene fornito con due millimetri pushrod / sfera-link (può essere cambiato per diverse lunghezze se necessario) e lega di 360 gradi staffe di montaggio.
Tensione di funzionamento: 4.8V ~ 6v
Dimensioni: 45mm x 16 x 16 millimetri
I have bought this item but didn't use it yet, not sure where I can use this item, I have to think about it, may be hatch door for dropping something from my model aircraft.I received mine. I ordered 4 of these. I was impressed with it until I tested one.
It was working, approximately a dozen "open / closes". all of the sudden, in closed position, it wouldn't open. I openned the unit to see what went wrong. There are 2 spring loaded type of switches at both ends. these swithes the limit swithces. one of the swithces (in closed position), got stuck. in this position the motor wouldn't turn. not sure what to do with 3 units I have. definitely not using them for gear door actuation due to reliability. I would however use them on other things that would not hurt my model.Good, strong and well built, but not well suited to u/c doors cos they have a slight backlash at each end of travel i.e. will pull door fully closed then back open very slightly.
Could be worked around by having some small flexibility in the door horn I guess, but not ideal in the scenario where a good, strong door closed position is required to prevent them being sucked open in some manoeuvres.Glad I ordered two when I needed only one. One works fine out of the box. The second tries to move as you switch it from one direction to the other. You can feel the motor kick then jam. Doesn't seem to be any way to un-jam it and costs too much to return for warranty. In the future, I'll remember to order several more than I need. Hope the one that works doesn't die in the air........
The push rod is a bit weak, but works. the fitting on the end works fine on a hinge. Overall, great design with a lot of potential. Then need to expand from 15 mm stroke to 20, 25 or even 30 in the future.Gewicht 29,24g mit 12,5cm abel mit Stecker
Gehaeuselaenge 64,5mm Querscnitt 14x16mm plus je 10mm Befestigungswinkel
Hub ca. 18mm Kugelkopfanschluss dabei
Nice unit comes with all hardware pictured to use straight away. Can't find a listing for alternate lentgh pushrods. Would be good if longer throws were availiable. Have two for nose gear doors in a VQ Invader.I have bought three of these units and two have failed. I was using them for gear door actuators in a jet using a 6v system. I lost the two failed units at switch on of the power system. I suspect that a spike when first switched on caused the failures. I wil test the other one in a 5 volt system and see if the problem re-occurs.I bought three of these and didn't really have a use for them at the time. But now, my A-10 canopy open/close stopped working so i have fitted one of these. Excellent bit of kit. Unit swivels on the mounting backets and allows great movement. Heaps of power and seems to have overload protection. Very easy to install and forget about. Works every time (the other one didn't) I now have plans for the other two and will order more. Great for air brakes, Gear doors and canopy. My air rams are off to the bin.This is a winner that gives 10mm approx of travel. It is an easier mounting solution than a servo for opening doors. However, the door hinging will need to be setup to swing the doors through more travel.This thing IS GREAT bye bye pneumatic rams.
AND it's also very strong. you won' tbe able to stop it.
very cool product and will be easy to mount