Il Wicked Ala XL vola come se fosse su rotaie! Responsive ancora controllabile e facile da pilotare. Aggiungete un po 'di zavorra per le pesanti (più ventoso) giorni al vostro pendenza locale e godere della
spensierato divertimento ad alta velocità solo un'ala di combattimento quasi indestuctable può fornire!
Sì, è CATTIVO - divertente Wicked che è!
Il Wicked Ala XL è in grado di essere diffondeva intorno alla pista in appena 10knots di vento o zavorrato up stile 'piombo slitta' per il divertimento ad alta velocità in 20 nodi più!
Costruito interamente in materiale EPP ad alta densità praticamente indistruttibile questo modello durerà per sempre - letteralmente! Il kit comprende parti di ricambio di carbonio che rendono questa ala flex libero - anche incluso nel kit è tutto l'hardware, il nastro di rinforzo e il nastro di copertura colorata, tutto quello che dovete aggiungere è una bottiglia di CA collante per unire le due metà dell'ala e trattenere i longheroni in carbonio nei loro alloggiamenti pre-tagliati.
Il sistema radio necessaria deve avere miscelazione delta di mescolare le superfici di controllo elevon. Aggiungi il ricevitore e un ricevitore pack 5 cellulare, insieme con la propria scelta di servi - servi sia standard e mini sono soddisfatti con pre pozzi servo taglio, si raccomanda di metallo orientato servi indipendentemente dalle dimensioni si sceglie ...... .Questo è un'ala di combattimento, dopo tutto!
Apertura alare: 1.525 millimetri
Lunghezza: 395 millimetri
Peso di volo: 900-1200g
core ala PPE
Spars in carbonio x 5
In fibra di vetro nastro di rinforzo
Colorato nastro di finitura
Kit hardware completa
4 canali radio con elevon (Delta) miscelazione
2 standard o mini servi (suggerisca metallo orientata)
batteria NiMH ricevitore 4 o 5 celle
Motorsize ( diam - o - cc )
Apertura alare ( mm ):
SaleWeight ( g )
Telaio / PNF / RTF ( mm )
IC / 2 : Elec:
Capacità ( mAh ):
very nice wing i have 2 of them no probloms with putting in 6v reviver battery in you have to make your own lid or just use bullet tape over the battery otherwise very simple buid works well if i had my way i would get few moreInstructions appear to be for the smaller version and aren't much use. Very easy to assemble. The grooves for the carbon are already cut and are a good fit. Plenty of fibre glass tape used with lots left. I got yellow and orange coloured tape and again plenty left. The supplied velcro for the wing ends looked too small and the wrong shape. I'm guessing it was for the smaller version of the wing. One aileron was slightly bowed and needed trimming to get it to fit against the wing. Despite the little errors I'm very pleased with how it came out and am looking forward to flying it. I tried off our local hill by myself in 25mph wings and couldn't launch it!!This is not a cheap version of anything. This wing is the 60 Scout Bee by Windrider, being sold by HobbyKing at a better price than Windrider sells it. I used the Hex MG-14 servos which fit and work perfectly. I skipped the strapping tape and used laminating material ("The New Stuff") then used EconoKote sparingly. I've flown this wing at Bluff Park in Long Beach, Dave's at Carlsbad, and Temple Hill in Pomona and it is a total blast to fly. A hawk bit a good size hole in it while at Temple Hill and it didn't miss a beat. I consider this one of my best purchases from HK. I highly recommend this slope wing.Great size wing, flown it from the local slope a few times now. Building was quick and simple, all the grooves for the carbon reinforcements were a perfect push fit. Came with a full roll of 3 inch fibre tape (uni-directional) and so was able to cover the entire wing with it. This not only increases the strength but also makes it easier for the decoration tape (also included) to adhere and not bubble up. Weight of equipment not an issue on this model - it has more than enough surface area. In fact, I suspect it could do with more weight to aid penetration in to wind. I have not tried ballasting it up yet, it has so far managed the various wind strengths just fine. Great wing to fly, enjoying it. Be aware though that this is a BIG wing (relatively) when assembled. Still, bigger flies better!it is my first sloap soarer,not previous expierience on riding the wind,but i must say this wing is incredible!!!! so steady in wind,i flew it with 12 kt wind and is like flyiing on rails as some one else wrote about it in this page.
easy to assemble, straight forward but previous expierience required for some points during assembly. no where instrucrtions for those noise generators included,so look on the net for positions on top in order to make noise!!!!
i recommend it and i will definetely buy it again if needed.
This is a great wing! Its well made, easy to build, strong and flies great as a slope soarer. Unfortunately a magpie took a serious disliking to mine when flying at Marks Park, Bondi. Trying to get away from it, I got behind the ridge and off the wing went - searched for an hour but it had vanished! If anyone finds it please comment. Anyway I just had to buy another - such great fun!Gluing the Wing together was easy enough. as did applying the re-enforced tape. Hint: before applying tape use 3M 77 spray adhesive . . . it helps to hold down the tape. What took me the most time (and I did take my time building the Wing) was fitting the servos, connecting rods and elevon connector. Need to take your time lining everything up.
Applying the re-enforced tape and the packing tape was took some skill. Hint: before applying tape use 3M 77 spray adhesive . . . it helps to hold down the tape.
The CG is close to what is recommended. I used a 4-cell nickel hydride battery and still had to as 6 ounces of lead to balance the Wing with just a touch of nose down. I found the stick on weights for auto tires worked great, especially the 1/4 and 1/2 oz. lead.
I have flown the Wicked Wing XL for the past few weeks and it is very impressive. A number of guys at our club were very impressed with my build and its excellent flight characteristics . . . most of them own wings of one nature or another and are excellent combat pilots.
This is a exceptional glider . . . it is absolutely amazing!
Jim D.Very easy to assemble it, very pleasant flight, it can handle huge weight if you put a larger motor... It came with additional items not mentioned in site that looks like whistles or sirens but no instructions about how put in the wing...Came in good conditition, long carbon spars and tape included. Also almost all necessary hardware. Foam is a bit brittle (seems as it was moulded with too low pressure) but will do the job once it is taped. Nice Wing overall.
Powered maiden will be in the next weeks. Seems to be "similar" to the Scout Bee ;) ... Nice: The option to fill up all the premoulded holes with the optional foam parts included. With these glued in you can place the servos, battery,and RX where ever you like (recommendend at least for the servos if you like motorize this wing).
file di clienti
Aile HKING Scaricare ora [160kb] No File Name Scaricare ora [142kb] Aile HKING Scaricare ora [160kb] My Wicked Wing XL with home made motor m Scaricare ora [189kb] No File Name Scaricare ora [303kb] Elevon_Setup-on_Turnigy-TXs.pdf Scaricare ora [471kb] Wicked Wing XL - Assembly Instructions Scaricare ora [1712kb] british bulldog Scaricare ora [78kb] wicked rebel force Scaricare ora [3.70Mb] wicked rebel force 2 Scaricare ora [4.12Mb]