New Items フォーラム
新規登録

Total Price

AU$0.00

Cart 0 Cart 0 Loading...

2725ブラシレスアウトランナーモーター1600kv

2725ブラシレスアウトランナーモーター1600kv

Now save save AU$0.00 AU$0.00

AU$16.02
ステータス:
在庫切れ!
SKU:
074000063
WANT FREE SHIPPING? Click here to find out more!

2725ブラシレスアウトランナーモーター1600kv

仕様:
寸法:27ミリメートルX 25ミリメートル
重量:35グラム
KV:1600回転数/ V
電圧:7.4V〜11.1V(2S〜3S)
最大電流:17A
最大電力:190ワット
シャフト:3ミリメートル

* 色は異なる場合があります

  • 単位 074000063
  • Brand -
  • 重量 53.0000
  • 長さ 85.00
  • Width 27.00
  • 高さ 70.00
  • KV ( RPM / V ) 1600.00
  • 最大電流( A ) 17.00
  • 抵抗( MH ) 0.00
  • 最大電圧( V ) 11.00
  • 電力( W ) 190.00
  • シャフトA (ミリメートル) 3.00
  • 長さB ( mm)の 20.00
  • 直径C (ミリメートル) 27.00
  • ことができます長さD (ミリメートル) 10.00
  • 総丈E (ミリメートル) 45.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Worked fine at first. Didn't take long to figure out there is a quality control issue with this motor. At about 3/4 throttle it came to a screeching halt. Drop throttle and start again with same results. Found out that the stator with the wire windings worked loose from the motor housing. At about 3/4 throttle it would start to spin on the housing and lose timing causing it to stop. All three of these motors i got do the same thing. So it wasnt just a fluke. I assume that separating the motor and glueing the stator on firmly will fix the issue. I am waiting for one to dry to test it.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Worked fine at first. Didn't take long to figure out there is a quality control issue with this motor. At about 3/4 throttle it came to a screeching halt. Drop throttle and start again with same results. Found out that the stator with the wire windings worked loose from the motor housing. At about 3/4 throttle it would start to spin on the housing and lose timing causing it to stop. All three of these motors i got do the same thing. So it wasnt just a fluke. I assume that separating the motor and glueing the stator on firmly will fix the issue. I am waiting for one to dry to test it.

good engine

put it on biks3

now learning to fly)

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

good engine

put it on biks3

now learning to fly)

whatever Ive writen before - forget it - this motor is rubbish. Bearing becoming hot on 3S, one of two was burning by using an 8x6 prop. POS

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

whatever Ive writen before - forget it - this motor is rubbish. Bearing becoming hot on 3S, one of two was burning by using an 8x6 prop. POS

nice little outrunner - bearings seems to be okay. easy to install - like shaft on both side.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

nice little outrunner - bearings seems to be okay. easy to install - like shaft on both side.

It is good motor but where is motor mount? draw more current, gives less thrust compared to other motors in it's size. It is not bad motor but also not very good one, something in between.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

It is good motor but where is motor mount? draw more current, gives less thrust compared to other motors in it's size. It is not bad motor but also not very good one, something in between.

Great little motor. Attached this my my makeshift hovercraft and worked a treat, plus the fact that it didn't cost a lot was a bonus.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Great little motor. Attached this my my makeshift hovercraft and worked a treat, plus the fact that it didn't cost a lot was a bonus.

Badly designed motor. They have decent grunt but the shaft is stupidly long at the rear and cannot be adjusted. You would think you can take the grub screws out and the housing the slide the shaft up? no.. took them apart... the stop of the shaft is fixed to the spinner, it's not sliding anywhere. They also have a chunky 4.2mm axl

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Badly designed motor. They have decent grunt but the shaft is stupidly long at the rear and cannot be adjusted. You would think you can take the grub screws out and the housing the slide the shaft up? no.. took them apart... the stop of the shaft is fixed to the spinner, it's not sliding anywhere. They also have a chunky 4.2mm axl

I ended up with six of these. admittedly I crashed my quad and bent two of the props. But then today while hovering one of the motor shafts sheared off at the groove where the e-clip holds it on. Which by the way is where the other two bent.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I ended up with six of these. admittedly I crashed my quad and bent two of the props. But then today while hovering one of the motor shafts sheared off at the groove where the e-clip holds it on. Which by the way is where the other two bent.

Good motor for this price. I run it in a flying wing with 1000mm(39.4in) wingspan and
460g(14.8oz) weigth. Prop 8x4(fold). 3S 850mA lipo. Goes unlimited vertical and has
around 5min motor runtime.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Good motor for this price. I run it in a flying wing with 1000mm(39.4in) wingspan and
460g(14.8oz) weigth. Prop 8x4(fold). 3S 850mA lipo. Goes unlimited vertical and has
around 5min motor runtime.

Very nice motor although I couldn't slide the shaft through without fear of damaging it. It would need a thin firewall for attaching it behind the propeller.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Very nice motor although I couldn't slide the shaft through without fear of damaging it. It would need a thin firewall for attaching it behind the propeller.

  1. 1
  2. 2
Customer files
DIY Hex using 2725 motors Download [156]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!