新規登録

Product Finder

設定

Useful links

ライブチャット
 
[["US","AU","GB","DE"]]
新規登録

5W白色LED合金ストリップ150ミリメートルX 12ミリメートル(3S互換)

5W白色LED合金ストリップ150ミリメートルX 12ミリメートル(3S互換)

Discontinued Product

Please continue searching for a similar product.
Stock:
OUT OF STOCK
重量:
10 g
SKU:
371000065
商品概要

5W白色LED合金ストリップ150ミリメートルX 12ミリメートル(3S互換)

仕様:
外形寸法:150×12ミリメートル
重量:8グラム
コネクタ:JST
ビーム角:120
パワー:5ワット
色温度:6000から6500±200Kと
電圧:11.1V-13.5V(3S Lipoly)
電流:300ミリアンペア
光束:400-450LM
演色指数:70-85
材質: アルミ板
寿命:50000時間
動作温度:-20 - 60度摂氏

*注:必ず消費電流が300ミリアンペア未満であるか、LEDストリップを損傷する危険性が行ってください
Product
Specifications

追加情報

  • 単位:
    371000065
  • Brand:
    いいえ
  • 重量(g )
    10.00
  • 長さ
    155.00
  • Width:
    5.00
  • 高さ:
    45.00
Community
Discussions
Rate&
Review

あなたのレビューを投稿する

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
I have to agree with the other reviewers on this LED strip. It claims it's 3S compatible, but it gets EXTREMELY hot when connected to a fully charged 3S pack. A resistor is necessary to run this with 3S.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I run them with a Meanwell LDD-300L (http://www.meanwell.com/mw_search/ldd-l/LDD-L-SPEC.PDF) switching DC current driver to ensure the leds are driven within rating despite the battery voltage (you can run them from about 10V to 36V input voltage). They are very bright, but only heat up to about 40C. Additionally, this driver has a PWM input (up to 1Khz, not servo-PWM) which I have connected to a GPIO of my Pixhawk flight controller using a N-FET inverter (the GPIO can't drive the current neccessary for the PWM input, I've used 100 Ohm in series to the gate for protection, 100K pull down on the gate and 1K pull up to the battery voltage on the drain). Using the PX4-built-in application gpio_led, the led stripes begin to blink when the battery reaches a low voltage. The PWM input can just left unconnected if not needed.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
They get very hot. Run at 9.0VDC and make sure of polarity. Some of the JST's are improperly assembled
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
This LED has been tested by me on my plane and have to say that in clear weather the LED was visible even at a distance of / - 350 m.
Led is on the leading edge of the wing glued with glue 302 HK.
as power supply is a 3s lipo and use a 10-ohm resistor-10watt.
Will in the future several models of these LEDs provide.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Do NOT connect it to fully charged 3S directly!
Never!
Only 2S
(or LiFePo4 half charged)

Good product!

It should work as a LED - via resistor or LED driver.

Vdrop:
8.40V * 200mA
8.69V * 300mA
8.95V * 400mA
9.07V * 450mA
9.22V * 500mA
Put resistor in series R=(Vbat - Vdrop)/I (choose current you want) Resistor 1-3W (P=(Vbat - Vdrop) * I )

Don't know how long it survive if get wet or in a cold weather.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Tested with 11.1V 3S lipo. Very bright although theres a need to keep the current to 300mA to prevent overheating.
*It is so bright it blinds ur eyes.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
tres lumineux, bien visible l'exterieur en pleine journee, chauffe assez fort, contrairement a ce qui est annonce le courant consomme est de 1,1 A sous 12V, ce qui fait plus de 12W, plein d'applications possibles...
verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

顧客ファイル
No File Name download now [1805kb]

商品のタグ

タグを区切るには空白を使って下さい。タグがフレーズの場合は、「'」で囲って下さい。