新規登録

Product Finder

設定

Useful links

ライブチャット
 
[["US","AU","GB","DE"]]
新規登録

55/64ミリメートルのためのTurnigy 2615 EDFアウトランナーの3000kv

55/64ミリメートルのためのTurnigy 2615 EDFアウトランナーの3000kv

Discontinued Product

Please continue searching for a similar product.
Stock:
OUT OF STOCK
重量:
100 g
SKU:
T26151D3000
商品概要
55/64ミリメートルのためのTurnigy 2615 EDFアウトランナーの3000kv
仕様:
3000 Kv-
寸法:52のx 26ミリメートル
シャフト:2.3 / 3.0ミリメートル
電圧:11.1V
重量:66グラム
現在の無負荷:1.2A
無負荷回転数:33900
負荷電流:12.5Aを
ロードRPM:29420
スラスト:390グラム
取付穴ボルトサークル:18ミリメートル
MTG。ホール数&サイズ:4×M2.5
 
2軸、2.3&3.0ミリメートルが含まれています
Product
Specifications

追加情報

  • 単位:
    T26151D3000
  • Brand:
    N/A
  • 重量(g )
    100.00
  • 長さ
    92.00
  • Width:
    45.00
  • 高さ:
    55.00
  • KV ( RPM / V )
    3000.00
  • 最大電流( A )
    12.50
  • 電力( W ):
    0.00
  • 長さB ( mm)の:
    52.00
  • ことができます長さD (ミリメートル)
    18.00
  • 最大電圧( V )
    11.00
  • シャフトA (ミリメートル):
    3.00
  • Unit Weight (g):
    66
  • 直径C (ミリメートル)
    26.00
  • 総丈E (ミリメートル)
    64.00
  • 抵抗( MH ):
    0.00
Community
Discussions
Rate&
Review

あなたのレビューを投稿する

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
A bit dissapointed with this motors now. They used to have 0,2mm stator plates, but now they have 0,35mm... probably a cheaper stator. The results is lower efficiency for the motor.

They do include 2 shafts, one with a 2,3mm (micrometer=2,27) tip and one extra 3mm (2,97 with micrometer)
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
This motor will power my new Babycat (Flycat) model with Tgs 4.75x4.75 prop, 25A ESC and 2S 1800mAh lipo cells.



In that configuration motor draws around 17A and produces 125W. More than enough power for small Babycat (800mm wingspan). With Tgs 5x5 prop you get 19A or 150W...



Motor is well made and came with 3mm shaft. Included are also another 3mm shaft and 2,3mm!



Only cons that I found is that there is no e-ring on the shaft. Most outrunners have e-ring or collar with grub screw, which fixes the rotor.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I'm using this motor in the Phase-3 Fantom/Phase-3 F-16 55mm three-blade fan unit on 4-cell 1750-2200 lipo, draws about 35 amps at full throttle and nice power upgrade for the original KMS 20mm inrunner motor. Also using on GWS F-15 on 4-cell 1750 and it works quite well. Will fly Phase 3 EDF Fantom on 3-cells as well, but performance is less.



Tried the 2810 motor first on the Fantom, but it burnt the windings on a 4-cell flight.



Great replacement for the orginal KMS 5100 KV inrunner motor if you want to fly on 4-cells instead of 3. One third the cost of the original motor.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
In Hawk 64mm Impeller mit 4S LIPO: 40'000 rpm, 600g Schub. Sehr gut!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
put this on a 7 blade 64mm fan only made 270 grams of thrust on 11 volt lipo maybe it will do better on a 68mm fan because 270 grams isnt going to hardly move a 64mm jet
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Tested with the blue EDF64mm also sold here:



Thrust(g) Amps Battery

200 5.1 800 3s20c

270 8.5 800 3s20c

330 10.0 1800 15c

370 12.3 1800 15c

440 15.0 2200 20c



My set resonates somewhere between 200-270g of thrust where light rubbing of the fan and case occurs. With that said the motor is smooth and remarkably quiet. This is quite a low current setup probably more suited for lighter 300g-400g AUW planes.
verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

商品のタグ

タグを区切るには空白を使って下さい。タグがフレーズの場合は、「'」で囲って下さい。