Turnigy統合PCBプラグアンドプレイマイクロクワッド（P＆P）

• Overall
• Quality
• Value

Customer Rated

Sep 14, 2012

The quad flys well. Only the motor mount tabs are very weak, i glued them with carbon fiber strips. Also the flight controller board is mounted without shock absorber. I used the following start setup:
Roll 45pcnt, Pitch 20pcnt Yaw 75pcnt.

• Overall
• Quality
• Value

Customer Rated

Sep 13, 2012

To say that this is ready to fly is an exggeration. I had to upgrade the firmware of mine to even get lift off, it came with a borked setup.

One of the motors are "lazy" and tend to not rev as hard as the other three, causing it to fall over on full throttle and will sometimes start the prop backwards when going from a full stop.

The ESCs are set to hard cutoff when the battery is low, and will quite simply drop dead in mid air.

However.. After a lot of tweaking and six broken props, it now flies REALLY well. Remains controllable in pretty heavy winds although the battery died real fast.

Has a nice 50pcnt throttle hover just like quad people tend to recommend.
Would probably lift a go pro bullet or even the full go pro camera.

• Overall
• Quality
• Value

Customer Rated

Sep 06, 2012

Aprs 1 mois d'utilisation,
ce quad est adorable ; on peut l'emmener partout.
Dommage que la valise en alu ne soit pas dans le package ; cela aurait t parfait.
J'ai vu qu'il existait une version hexa ; je vais de ce pas commander 2 moteurs, 2 ESC et le programmateur de la carte pour tester.
Bons Vols

• Overall
• Quality
• Value

Customer Rated

Sep 02, 2012

Just maidened mine two days ago. OMG this is like crack! But I went through quite a lot more setup than expected and ended up doing a major modification to add carbon fiber arms (see attached photo).

There were three problems:
1) Gyro setups: yaw had to be reversed (procedure is explained in the manual). The pitch and roll gyro gains were way too large causing it to ocillate. After turning the pots down it is *very* stable.

2) The PCB material is very brittle for arm material. Broke an arm on the second flight. After a lot of glue later I decided to replace all four with carbon fiber extensions bolted down (see photo in files). Now its rock solid.

3) The power leads are not tethered/constrained at all. Both broke before even the first flight trying to tie down the battery. Beef up the solder and add tie straps!

I'm flying with the 850mah nano techs and get 8:30 min flights! This thing is so awesome now.

• Overall
• Quality
• Value

Customer Rated

Aug 28, 2012

Super der Zwerg!! Fliegt sich perfekt und das gleich aus dem Karton!
Verarbeitung ist auch top!
Kann ich jedem Empfehlen!

• Overall
• Quality
• Value

Certified Buyer Rated

Aug 23, 2012

not so plug and play, be prepared to fiddle with the board, learn how to change the gyro directions and look up witch way the motors should spin.

• Overall
• Quality
• Value

Customer Rated

Aug 22, 2012

Bozos,

I finally got my new 250 mm HK quad into the air after, lets say, about half an hourish of tinkering. A slight adjustment to the rolling plane gyro was necessary for perfect stable hover/flight.

Robbie was there and his mouth is still open.

This is an impressive li'll unit and is much more sophisticated than the MQX equivalent. It is equally as stable and flys just as well, in my garage. I'll try it in open spaces later in the week. I have no doubt that it is as quick and manoeuvrable as the MQX. Neither like the wind.

Any one considering getting an MQX ($160), or equivalent should review this unit first.

Don't misunderstand me, I love my MQX and it's 10 minute plus flight times are far superior to this unit.

I believe the motors in the MQX are brushed coreless. The board is integrated with no separate components.

This unit consists of the following separate components. Four brushless motors, four Turnigy Plush 6 amp esc/s, frame, props and board and it is assembled. Check all components and fittings before flight.

Cost is $110 including freight with an optional aluminium case available.

I gave this five stars because four and a half stars isn't an option. Nothing is perfect. This is close.

Cheerz from Australia.

• Overall
• Quality
• Value

Customer Rated

Aug 21, 2012

Good product, although you can buy all pieces separetely and work them together for less money.
There is no low voltage protection, so be careful. Use a Volt Watch Meter.
The manual is not complete, so here follow some tips:
- To zero the yaw pot, rotate it counter clock wise (left)
- The flight controller takes about 8 seconds do beep twice (necessary to adjust the throttle range, see manual). Before this, there are some start up sounds.
- All my engines are rotating the inverse direction, but it does not matter. Just position the props accordingly.
- Some engines start before others, but it also does not matter. As soon as the power is enough to fly, the rotation will equalize.
- Stick four balsa (1.5cm) sticks at each end, protecting the props from hard landing and wall crashing.
- First time configuring the flight controller, the engines did not start. Some versions need you to lower the power and go full rudder right (hold) until led lights (do it in a flat surface). If it does not work, try reversing rudder channel.
- Try hovering for one sec few inches above floor in a place without wind until you learn to stand still. Good flight!

• Overall
• Quality
• Value

Customer Rated

Aug 12, 2012

Disappointing product. Not working.. we bought 3 units,, all same useless Cannot setting as manual instruction. motor can run.. but aileron, elevator, rudder all not function,, can't fly at all, now want to return to HK.. wasted lots of shipping fees that not refund..

• Overall
• Quality
• Value

Certified Buyer Rated

Aug 11, 2012

It's a bit tricky to set up but it flies. Make sure you remove propeller when you reverse gyros, I did the mistake of not removing them and I paid the price (it cut my fingers)! On my first flight it flipped in the wind and the dome thing at the top broke as well as 2 blades. Luckily I included spares in my order. By the way, the transmitter I'm using is T6. Ask me if you need help!